ASTM D 6117 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes
Hardcopy , PDF
14-07-2023
English
14-06-2018
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These test methods cover the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures.
1.2The test methods appear in the following order:
| Sections | ||
| Test Method A—Nail, Staple, or Screw Withdrawal Test | 4 to 13 | |
| Test Method B—Lateral Nail, Staple, or Screw Resistance Test | 14 to 22 |
1.3Plastic lumber and plastic shapes are currently made predominately from recycled plastics. However, these test methods would also be applicable to similar manufactured plastic products made from virgin resins where the product is non-homogeneous in the cross-section.
1.4The values stated in inch-pound units are to be regarded as standard. The SI units given in parentheses are for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 6341 : 2016 | Standard Test Method for Determination of the Linear Coefficient of Thermal Expansion of Plastic Lumber and Plastic Lumber Shapes Between –30 and 140°F (–34.4 and 60°C) |
| ASTM D 6111 : 2019 : REV A | Standard Test Method for Bulk Density And Specific Gravity of Plastic Lumber and Shapes by Displacement |
| ASTM D 6341 : 1998 | Standard Test Method for Determination of the Linear Coefficient of Thermal Expansion of Plastic Lumber and Plastic Lumber Shapes Between -30 and 140°F (-34.4 and 60°C) |
| ASTM D 6111 : 2018 | Standard Test Method for Bulk Density And Specific Gravity of Plastic Lumber and Shapes by Displacement |
| ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM D 6111 : 2019 | Standard Test Method for Bulk Density And Specific Gravity of Plastic Lumber and Shapes by Displacement |
| ASTM D 6341 : 2021 | Standard Test Method for Determination of the Linear Coefficient of Thermal Expansion of Plastic Lumber and Plastic Lumber Shapes Between –30 and 140°F (–34.4 and 60°C) |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM D 1761 : 1988 : R1995 : EDT 1 | Standard Test Methods for Mechanical Fasteners in Wood |
| ASTM D 6111 : 1997 | Standard Test Method for Bulk Density and Specific Gravity of Plastic Lumber and Shapes by Displacement |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.