ASTM D 6311 : 1998 : R2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Generation of Environmental Data Related to Waste Management Activities: Selection and Optimization of Sampling Design
Hardcopy , PDF
11-11-2014
English
10-09-1998
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 11.04, 2015 Gives practical guidance on the optimization and selection of sample designs in waste management sampling activities, within the context of the requirements established by the data quality objectives or other planning process.
| Committee |
D 34
|
| DocumentType |
Guide
|
| Pages |
25
|
| ProductNote |
Reconfirmed 2003
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This document provides practical guidance on the selection and optimization of sample designs in waste management sampling activities, within the context of the requirements established by the data quality objectives or other planning process.
1.2 This document (1) provides guidance for selection of sampling designs; (2) outlines techniques to optimize candidate designs; and (3) describes the variables that need to be balanced in choosing the final optimized design.
1.3 The contents of this guide are arranged by section as follows:
| 1. | Scope |
| 2. | Referenced Documents |
| 3. | Terminology |
| 4. | Significance and Use |
| 5. | Summary of Guide |
| 6. | Factors Affecting Sampling Design Selection |
| 6.1 Sampling Design Performance Characteristics | |
| 6.2 Regulatory Considerations | |
| 6.3 Project Objectives | |
| 6.4 Knowledge of the Site | |
| 6.5 Physical Sample Issues | |
| 6.6 Communication with the Laboratory | |
| 6.7 Analytical Turn Around Time | |
| 6.8 Analytical Method Constraints | |
| 6.9 Health and Safety | |
| 6.10 Budget/Cost Considerations | |
| 6.11 Representativeness | |
| 7. | Initial Design Selection |
| 8. | Optimization Criteria |
| 9. | Optimization Process |
| 9.2 Practical Evaluation of Design Alternatives | |
| 9.3 Statistical and Cost Evaluation | |
| 10. | Final Selection |
| Annex A1. | Types of Sampling Designs |
| A1.1 Commonly Used Sampling Designs | |
| A1.2 Sampling Design Tools | |
| A1.3 Combination Sample Designs | |
| Appendix X1. Additional References | |
| Appendix X2. Choosing Analytical Method Based on Variance and Cost | |
| Appendix X3. Calculating the Number of Samples: A Statistical Treatment |
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 6956 : 2017 | Standard Guide for Demonstrating and Assessing Whether a Chemical Analytical Measurement System Provides Analytical Results Consistent with Their Intended Use |
| ASTM D 7353 : 2007 : R2013 | Standard Practice for Sampling of Liquids in Waste Management Activities Using a Peristaltic Pump |
| ASTM D 5681 : 2018 | Standard Terminology for Waste and Waste Management |
| ASTM D 5680 : 2014 | Standard Practice for Sampling Unconsolidated Solids in Drums or Similar Containers |
| ASTM D 6538 : 2012 | Standard Guide for Sampling Wastewater With Automatic Samplers |
| ASTM D 5792 : 2010 : R2015 | Standard Practice for Generation of Environmental Data Related to Waste Management Activities: Development of Data Quality Objectives |
| ASTM D 6759 : 2016 | Standard Practice for Sampling Liquids Using Grab and Discrete Depth Samplers |
| ASTM D 7758 : 2017 | Standard Practice for Passive Soil Gas Sampling in the Vadose Zone for Source Identification, Spatial Variability Assessment, Monitoring, and Vapor Intrusion Evaluations |
| ASTM D 6982 : 2009 : R2016 | Standard Practice for Detecting Hot Spots Using Point-Net (Grid) Search Patterns |
| ASTM D 7204 : 2015 | Standard Practice for Sampling Waste Streams on Conveyors |
| ASTM D 6232 : 2016 : REDLINE | Standard Guide for Selection of Sampling Equipment for Waste and Contaminated Media Data Collection Activities |
| ASTM D 6051 : 2015 | Standard Guide for Composite Sampling and Field Subsampling for Environmental Waste Management Activities |
| ASTM D 5956 : 2015 | Standard Guide for Sampling Strategies for Heterogeneous Wastes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.