ASTM D 6382/D6382M : 1999 : R2022
Current
The latest, up-to-date edition.
Standard Practice for Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material
Hardcopy , PDF
English
08-11-2022
Committee |
D 08
|
DocumentType |
Standard Practice
|
Pages |
3
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This practice covers test procedures and conditions that are applicable when Test Methods D5023, D5024, D5026, D5279, and D5418 are used for conducting dynamic mechanical analysis of roofing and waterproofing membrane material in three-point bending, compression, tension, torsion, and dual cantilever modes, respectively. The specific method is selected by the analyst and depends on the membrane material and the operating principles of the individual instrument used for the analysis.
1.2This practice covers test procedures and conditions that are applicable when Test Method E1131 is used for conducting thermogravimetry of roofing and waterproofing membrane material.
1.3Membrane materials include bituminous built-up roofing, polymer-modified bitumen sheets, vulcanized rubbers, non-vulcanized polymeric sheets, and thermoplastics. The membrane materials can be either nonreinforced or reinforced.
1.4This practice is applicable to new membrane materials received from the supplier, those exposed artificially in the laboratory or outdoors on an exposure rack, and those sampled from field installations.
1.5This practice contains notes which are explanatory and are not part of the mandatory requirements of this practice.
1.6The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 4637/D4637M : 2015 : R2021 : EDT 1 | Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane |
ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
ASTM E 473 : 2022 : REV D | Standard Terminology Relating to Thermal Analysis and Rheology |
ASTM D 5024 : 2023 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Compression |
ASTM D 5023 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending) |
ASTM D 1079 : 2020 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 5418 : 2023 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Dual Cantilever Beam) |
ASTM E 1142 : 2022 : REV C | Standard Terminology Relating to Thermophysical Properties |
ASTM E 473 : 2023 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
ASTM D 5026 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Tension |
ASTM D 5024 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Compression |
ASTM D 5418 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Dual Cantilever Beam) |
ASTM E 1142 : 2024 | Standard Terminology Relating to Thermophysical Properties |
ASTM D 5023 : 2023 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending) |
ASTM E 1142 : 2023 | Standard Terminology Relating to Thermophysical Properties |
ASTM D 1079 : 2024 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 5026 : 2023 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Tension |
ASTM E 473 : 2023 : REV B | Standard Terminology Relating to Thermal Analysis and Rheology |
ASTM E 473 : 2023 | Standard Terminology Relating to Thermal Analysis and Rheology |
ASTM E 1142 : 2023 : REV B | Standard Terminology Relating to Thermophysical Properties |
ASTM E 1142 : 2023 : REV A | Standard Terminology Relating to Thermophysical Properties |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.