ASTM D 6448 : 2016 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
15-06-2022
English
22-04-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 05.03, 2016 Defines four grades of fuel oil made in whole or in part with hydrocarbon-based used or reprocessed lubricating oil or functional fluids, such as preservative and hydraulic fluids.
| Committee |
D 02
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers four grades of fuel oil made in whole or in part with hydrocarbon-based used or reprocessed lubricating oil or functional fluids, such as preservative and hydraulic fluids. The four grades of fuel are intended for use in various types of fuel-oil-burning industrial equipment under various climatic and operating conditions. These fuels are not intended for use in residential heaters, small commercial boilers, combustion engines, or marine applications,
1.1.1Grades RFO4, RFO5L, RFO5H, and RFO6 are used lubricating oil blends, with or without distillate or residual fuel oil, or both, of increasing viscosity and are intended for use in industrial burners equipped to handle these types of recycled fuels.
Note 1:For information on the significance of the terminology and test methods used in this specification, see Appendix X1.
1.2This specification is for use in contracts for the purchase of fuel oils derived from used lubricating oil and for the guidance of consumers of such fuels. This specification does not address the frequency with which any particular test must be run.
1.3Nothing in this specification shall preclude observance of national or local regulations, which can be more restrictive. In some jurisdictions, used oil is considered a hazardous waste and fuels from used oil are required to meet certain criteria before use as a fuel.
Note 2:For United States federal requirements imposed on used oil generators, transporters and transfer facilities, reprocessors, marketers, and burners, see 40 CFR 279.
Note 3:The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865.
1.4The values stated in SI units are to be regarded as standard; non-SI units, when given, are for information only.
| ASTM D 6823 : 2008 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
| NFPA 31 : 2016 | INSTALLATION OF OIL-BURNING EQUIPMENT |
| ASTM D 6823 : 2008 : R2013 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
| NFPA 1 : 2021 | FIRE CODE |
| ASTM D 7666 : 2012 | Standard Specification for Triglyceride Burner Fuel |
| NFPA 1 : 2018 | FIRE CODE |
| ASTM D 3245 : 2003 | Standard Test Method for Pumpability of Industrial Fuel Oils (Withdrawn 2010) |
| CFR 40(PTS266-299) : JUL 2017 | PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY |
| ASTM D 2709 : 2016 : REDLINE | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 1217 : 2015 : REDLINE | Standard Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer |
| ASTM D 129 : 2013-08 | TEST METHOD FOR SULFUR IN PETROLEUM PRODUCTS (GENERAL HIGH PRESSURE DECOMPOSITION DEVICE METHOD) |
| ASTM D 4868 : 2017 : REDLINE | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels |
| ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
| ASTM D 240 : 2017 : REDLINE | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter |
| ASTM D 2622 : 2016 : REDLINE | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 1481 : 2017 : REDLINE | Standard Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Lipkin Bicapillary Pycnometer |
| ASTM D 1480 : 2015 : REDLINE | Standard Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Bingham Pycnometer |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.