ASTM D 6750 : 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur)
Hardcopy , PDF
11-11-2014
English
15-10-2008
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
68
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 These test methods cover the performance of engine oils intended for use in certain diesel engines. They are performed in a standardized high-speed, single-cylinder diesel engine by either the 1K (0.4 % fuel sulfur) or 1N (0.04 % fuel sulfur) procedure. The only difference in the two test methods is the fuel used. Piston and ring groove deposit-forming tendency and oil consumption are measured. Also, the piston, the rings, and the liner are examined for distress and the rings for mobility. These test methods are required to evaluate oils intended to satisfy API service categories CF-4 and CH-4 for 1K, and CG-4 for 1N of Specification D 4485
1.2 These test methods, although based on the original Caterpillar 1K/1N procedures, also embody TMC information letters issued before these test methods were first published. These test methods are subject to frequent change. Until the next revision of these test methods, TMC will update changes in these test methods by the issuance of information letters which shall be obtained from TMC (see Annex A15).
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements appear throughout the text. Being engine tests, these test methods do have definite hazards that shall be met by safe practices (see Annex A16 on Safety Precautions).
1.5 The following is the Table of Contents:
Section | ||
Introduction | ||
Scope | 1 | |
Referenced documents | 2 | |
Terminology | 3 | |
Summary of Test Methods | 4 | |
Significance and Use | 5 | |
Apparatus | 6 | |
General Laboratory Requirements | 6.1 | |
Test Engine | 6.2 | |
Test Engine Accessories and Parts | 6.3 | |
Reagents and Materials | 7 | |
Test Oil Sample Requirements | 8 | |
Preparation of Apparatus | 9 | |
Engine Inspection | 9.1 | |
Engine Pre-Test Lubrication System Flush | 9.2 | |
Engine Pre-Test Measurements and Inspections | 9.3 | |
Engine Assembly | 9.4 | |
Pressure Testing of Fuel System Assembly | 9.5 | |
Calibration of Engine Test Stand | 10 | |
General Requirements and Frequency of Calibration | 10.1 | |
Runs | 10.2 | |
Specified Test Parameters | 10.3 | |
Calibration Test Acceptance Criteria | 10.4 | |
Action on Rejection of Calibration Test | 10.5 | |
Test Numbering | 10.6 | |
Reference Oils | 10.7 | |
Severity Adjustments | 10.8 | |
Engine Operating Procedure | 11 | |
Engine Run-In | 11.1 | |
Cool-Down Procedure | 11.2 | |
Warm-Up Procedure | 11.3 | |
Operating Conditions and Oil Additions | 11.4 | |
Measurement of Oil Consumption | 11.5 | |
Sampling Used Oil | 11.6 | |
Shutdowns, Lost Time and Off Tolerance Conditions | 11.7 | |
Recording of Exhaust Temperature | 11.8 | |
Air-Fuel Ratio Measurement | 11.9 | |
Recording of Engine Conditions | 11.10 | |
Humidity Requirements/Calibration/Measurement | 11.11 | |
Inspections, Photographs and Measurements | 12 | |
Reference to Reporting Form | 12.1 | |
Pre-Test Measurements of Engine Parts | 12.2 | |
Post-Test Information | 12.3 | |
Oil Inspections | 12.4 | |
Report | 14 | |
General Directions | 14.1 | |
Electronic Transmission of Test Results (Optional) | 14.2 | |
Reporting Calibration Test Results | 14.3 | |
Precision and Bias | 15 | |
Keywords | 16 | |
ANNEXES | ||
Specifications for Test Engine and Engine Build | Annex A1 | |
Intake Air System Details | Annex A2 | |
Exhaust System Details | Annex A3 | |
Cooling System Details | Annex A4 | |
Oil System Modifications and Instrument Locations | Annex A5 | |
Other Pressure and Temperature Measurement Locations | Annex A6 | |
Oil Consumption Linear Regression Method | Annex A7 | |
Test Fuel Specifications | Annex A8 | |
Lubrication System, Flush Apparatus and Procedure | Annex A9 | |
Engine Operating Conditions | Annex A10 | |
Procedure for Rating Piston and Liner | Annex A11 | |
Calculation of Percent Offset and Percent Deviation | Annex A12 | |
1K/1N Test Reporting | Annex A13 | |
Parts List by Part Number (P/N) and Warranty | Annex A14 | |
Role of Test Monitoring Center | Annex A15 | |
Safety Precautions | Annex A16 | |
APPENDIXES | ||
Humidity Data | Appendix X1 | |
Statistical Equations for Mean and Standard Deviation | Appendix X2 | |
Examples of Forms for Reporting | Appendix X3 | |
Optional Recording of Oil Pass Limits | Appendix X4 |
ASTM D 7589 : 2016 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine<rangeref></rangeref > |
ASTM D 6837 : 2013 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIB Spark Ignition Engine<rangeref></rangeref > (Withdrawn 2022) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.