ASTM D 6779 : 2004 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
Hardcopy , PDF
11-11-2014
English
01-11-2004
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
13
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 This classification system covers polyamide materials suitable for molding and extrusion. Some of these compositions are also suitable for application from solution.
1.2 This classification system allows for the use of recycled polyamide materials provided that the requirements as stated in this classification system are met. The proportions of recycled material used, as well as the nature and amount of any contaminant, however, cannot be covered practically in this specification.
1.3 The properties included in this classification system are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specialized applications. These may be specified by using the suffixes as given in Section .
1.4 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system.
1.5 The values stated in SI units are to be regarded as the standard.
This classification system is similar to ISO 1874-1/-2 1993, although the technical content is significantly different.
ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
ASTM D 955 : 2008 : R2014 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics |
ASTM F 2807 : 2013 : R2018 | Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications (Withdrawn 2024) |
ASTM D 5628 : 2018 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
ASTM D 5989 : 2018 | Standard Specification for Extruded and Monomer Cast Shapes Made from Nylon (PA) |
ASTM F 3091/F3091M : 2014 | Standard Specification for Powder Bed Fusion of Plastic Materials |
ASTM G 175 : 2013 | Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications |
ASTM F 2785 : 2018 : REV A | Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings |
ASTM F 2600 : 2009 : R2018 | Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing |
ASTM D 5740 : 2018 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
ASTM F 1733 : 2013 | Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing |
ASTM D 789 : 2018 | Standard Test Method for Determination of Relative Viscosity of Concentrated Polyamide (PA) Solutions |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.