Skip to content
Please enter a keyword to search

  • ASTM F 2807 : 2013 : R2018

    Current The latest, up-to-date edition.

    Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2018

    Publisher:  American Society for Testing and Materials

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 08.04, 2018 Defines requirements and test methods for 1/2 in. through 14 in. multilayer polyethylene-polyamide (PE-PA) pipe, which is a two-layer pipe (PE pipe layer bonded to an inner layer of PA).

    Scope - (Show below) - (Hide below)

    1.1This specification covers requirements and test methods for 1/2in. through 14 in. multilayer polyethylene-polyamide (PE-PA) pipe, which is a two-layer pipe (PE pipe layer bonded to an inner layer of PA). The multilayer pipe covered by this specification is intended for use in piping applications where the permeation and chemical resistance of polyamide (PA) compounds may be useful to protect the PE pipe layer, such as oil and gas producing applications that convey oil, dry or wet gas, and multiphase fluids.

    Note 1:Permeability and chemical resistance depends on the type of PA used. The PA layer delays but does not prevent liquid hydrocarbons effects. Therefore, the hydrocarbon chemical design factor for this multilayer pipe should be the same as for PE pipe layer—see X1.2.

    1.2Electrofusion and mechanical joints are typically used for this multilayer pipe.

    1.3Unless specified otherwise, all the pipe requirements in this specification are for the multilayer pipe.

    1.4The PA layer is not taken into consideration for the design pressure of multilayer pipe meeting this specification. Design pressure rating is determined from the PE pipe layer alone—see Appendix X1.

    1.5Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.6The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in figures and tables) shall not be considered as requirements of the standard.

    1.7The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee F 17
    Document Type Standard
    Product Note Reconfirmed 2018
    Publisher American Society for Testing and Materials
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 2837 : 2013 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
    ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 6779 : 2002 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 6779 : 2005 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 6779 : 2020 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 6779 : 2007 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 2290 : 2016 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
    ASTM D 1598 : 2002 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
    ASTM D 2122 : 1998 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 2290 : 2019 : REV A Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
    MIL-STD-129 Revision R:2014 Military Marking for Shipment and Storage
    ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
    ASTM D 1598 : 2015 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
    ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
    ASTM D 4218 : 2020 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
    ASTM D 1598 : 2015 : REV A Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
    ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
    ASTM D 2837 : 2001 : REV A Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
    ASTM D 6779 : 2003 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 1603 : 2001 Standard Test Method for Carbon Black In Olefin Plastics
    ASTM D 3350 : 2000 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 6779 : 2011 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 1598 : 2023 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
    ASTM D 3350 : 2008 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 6779 : 2008 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 4218 : 1996 : R2001 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
    ASTM D 2837 : 2002 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
    ASTM D 2837 : 2001 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
    ASTM F 1290 : 1998 : REV A : R2004 Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
    ASTM D 3350 : 2021 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 2837 : 2004 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
    ASTM D 2837 : 2021 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
    ASTM D 6779 : 2017 : REDLINE Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 3350 : 2002 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 6779 : 2004 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
    PPI TR 3 : 2017 POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
    ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 3350 : 2014 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 4218 : 1996 : R2008 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
    ASTM D 6779 : 2012 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 2290 : 2004 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
    ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 2837 : 2008 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
    ASTM D 6779 : 2006 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 2837 : 1998 : REV A Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
    ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 1598 : 1997 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
    EN 14125:2013 Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
    ASTM D 2837 : 2001 : REV A : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
    ASTM D 3350 : 2004 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 1603 : 2020 Standard Test Method for Carbon Black Content in Olefin Plastics
    ASTM D 2837 : 2011 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
    ASTM D 3350 : 2002 : REV A Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 1599 : 2014 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
    ASTM D 1599 : 2014 : EDT 1 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
    ASTM D 3350 : 2012 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 3350 : 2001 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 1603 : 2011 Standard Test Method for Carbon Black Content in Olefin Plastics
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ASTM D 1603 : 2014 : REDLINE Standard Test Method for Carbon Black Content in Olefin Plastics
    ASTM D 3350 : 2012 : EDT 1 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 2122 : 1998 : EDT 1 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    FED-STD-123 Revision H:2007 MARKING FOR SHIPMENT (CIVIL AGENCIES)
    ASTM D 1603 : 1994 Standard Test Method for Carbon Black In Olefin Plastics
    ASTM D 1599 : 2018 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
    ASTM D 2837 : 2022 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
    ASTM D 1599 : 1999 : R2011 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
    ASTM D 2290 : 2000 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
    ASTM D 1603 : 2006 Standard Test Method for Carbon Black Content in Olefin Plastics
    ASTM D 1599 : 1999 : EDT 1 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
    ASTM D 6779 : 2004 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM F 2619/F2619M : 2013 : REDLINE Standard Specification for High-Density Polyethylene (PE) Line Pipe
    ASTM D 6779 : 2023 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 4218 : 2015 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
    ISO 8510-2:2006 Adhesives Peel test for a flexible-bonded-to-rigid test specimen assembly Part 2: 180 peel
    ASTM D 2122 : 2022 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
    ASTM D 6779 : 2012 : REV A Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 3350 : 2010 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM F 1290 : 1998 : REV A : R2011 Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
    ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
    ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
    ASTM D 1598 : 2021 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
    ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 1598 : 2002 : R2008 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
    ASTM D 6779 : 2002 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 3350 : 2006 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 2290 : 2016-12 TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE
    ASTM D 2290 : 2000 : EDT 1 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
    ASTM D 2122 : 1998 : R2004 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 3350 : 2010 : REV A Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM F 1290 : 1998 : REV A Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
    ASTM D 2290 : 2019 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
    ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 1603 : 2014 Standard Test Method for Carbon Black Content in Olefin Plastics
    ASTM D 1603 : 2012 Standard Test Method for Carbon Black Content in Olefin Plastics
    ASTM D 1599 : 1999 : R2005 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
    ASTM D 1598 : 2002 : R2009 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
    ASTM D 2290 : 2012 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
    ASTM D 6779 : 2016 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 6779 : 2007 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 6779 : 2021 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 6779 : 2010 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 2122 : 1998 : R2010 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    SAE J 2260 : 2004 NONMETALLIC FUEL SYSTEM TUBING WITH ONE OR MORE LAYERS
    ASTM D 2290 : 2008 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
    ASTM D 1599 : 1999 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
    ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
    ASTM D 3350 : 2005 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 2122 : 2015 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 6779 : 2017 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 4218 : 1996 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
    ASTM D 6779 : 2008 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 6779 : 2006 : EDT 1 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
    ASTM D 2837 : 2013 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
    ASTM D 2837 : 2004 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective