ASTM D 6780 : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Water Content and Density of Soil in Place by Time Domain Reflectometry (TDR)
Hardcopy , PDF
11-11-2014
ASTM D 6780/D6780M : 2012
ASTM D 6780/D6780M : 2012 : REDLINE
English
01-05-2005
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 04.09, 2009 Covers soils that have 30 % or less by weight of their particles retained on the 19.0-mm ( 3/4-in.) sieve.
| Committee |
D 18
|
| DocumentType |
Test Method
|
| Pages |
13
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method may be used to determine the water content of soils and the in-place density of soils using a TDR apparatus.
1.2 This test method applies to soils that have 30 % or less by weight of their particles retained on the 19.0-mm ( 3/4-in.) sieve.
1.3 This test method is suitable for use as a means of acceptance for compacted fill or embankments.
1.4 This test method may not be suitable for organic and highly plastic soils.
1.5 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026.
1.5.1 The method used to specify how data are collected, calculated, or recorded in this standard is not directly related to the accuracy to which the data can be applied in design or other uses, or both. How one applies the results obtained using this standard is beyond its scope.
1.6 Two alternative procedures are provided.
1.6.1 Procedure A involves two tests in the field, an in-place test and a test in a mold containing material excavated from the in-place test location. The apparent dielectric constant is determined in both tests.
1.6.2 Procedure B involves only an in-place test by incorporating a bulk electrical conductivity in addition to the apparent dielectric constant.
1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. For additional information consult ASTM SI 10
1,8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM E 1 : 2014 : REDLINE | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM D 3740 : 2012-06 | PRACTICE FOR MINIMUM REQUIREMENTS FOR AGENCIES ENGAGED IN TESTING AND/OR INSPECTION OF SOIL AND ROCK AS USED IN ENGINEERING DESIGN AND CONSTRUCTION |
| ASTM D 698 : 2013-05 | TEST METHODS FOR LABORATORY COMPACTION CHARACTERISTICS OF SOIL USING STANDARD EFFORT (12400 FT-LBF/FT[3] (600 KN-M/M[3])) |
| IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
| ASTM D 4753 : 2015 : REDLINE | Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing |
| ASTM D 6026 : 2013 : REDLINE | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 653 : 2014 : REDLINE | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.