ASTM D 7042 : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
Hardcopy , PDF
27-08-2020
English
01-12-2019
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
13
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers and specifies a procedure for the concurrent measurement of both the dynamic viscosity, η, and the density, ρ, of liquid petroleum products and crude oils, both transparent and opaque. The kinematic viscosity, ν, can be obtained by dividing the dynamic viscosity, η, by the density, ρ, obtained at the same test temperature.
1.2The result obtained from this test method is dependent upon the behavior of the sample and is intended for application to liquids for which primarily the shear stress and shear rate are proportional (Newtonian flow behavior).
1.3The precision has only been determined for those materials, viscosity ranges, density ranges, and temperatures as indicated in Section 15 on Precision and Bias. The test method can be applied to a wider range of materials, viscosity, density, and temperature. For materials not listed in Section 15 on Precision and Bias, the precision and bias may not be applicable.
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7155 : 2018 | Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils |
ASTM D 2270 : 2010 : R2016 | Standard Practice for Calculating Viscosity Index from Kinematic Viscosity at 40 °C and 100 °C |
ASTM D 6823 : 2008 : R2013 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
ASTM D 7720 : 2011 : R2017 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
ASTM F 3337 : 2019 | Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil |
ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 2161 : 2019 | Standard Practice for Conversion of Kinematic Viscosity to Saybolt Universal Viscosity or to Saybolt Furol Viscosity |
ASTM D 8181 : 2019 | Standard Specification for Microemulsion Blendstock for Preparing Microemulsion Test Fuel Oils |
ASTM D 4054 : 2019 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
ASTM D 2502 : 2014 : R2019 | Standard Test Method for Estimation of Mean Relative Molecular Mass of Petroleum Oils from Viscosity Measurements |
ASTM D 2501 : 2014 : R2019 | Standard Test Method for Calculation of Viscosity-Gravity Constant (VGC) of Petroleum Oils |
ASTM D 7973 : 2019 | Standard Guide for Monitoring Failure Mode Progression in Plain Bearings |
ASTM D 3699 : 2019 | Standard Specification for Kerosine |
ASTM D 396 : 2019 : REV A | Standard Specification for Fuel Oils |
ASTM D 1655 : 2019 : REV A | Standard Specification for Aviation Turbine Fuels |
ASTM F 3208 : 2019 | Standard Guide for Selecting Test Soils for Validation of Cleaning Methods for Reusable Medical Devices |
ASTM D 7826 : 2019 : REV A | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
ASTM D 7152 : 2011 : R2016 : EDT 1 | Standard Practice for Calculating Viscosity of a Blend of Petroleum Products |
ASTM D 2880 : 2018 : REV A | Standard Specification for Gas Turbine Fuel Oils |
ASTM D 6751 : 2020 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 7666 : 2012 : R2019 | Standard Specification for Triglyceride Burner Fuel |
ASTM D 975 : 2019 : REV C | Standard Specification for Diesel Fuel |
ASTM D 4174 : 2017 | Standard Practice for Cleaning, Flushing, and Purification of Petroleum Fluid Hydraulic Systems |
ASTM D 341 : 2017 | Standard Practice for Viscosity-Temperature Charts for Liquid Petroleum Products |
ASTM D 5372 : 2017 | Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids |
ASTM D 6074 : 2015 | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
ASTM D 6710 : 2017 | Standard Guide for Evaluation of Hydrocarbon-Based Quench Oil |
ASTM D 7223 : 2017 | Standard Specification for Aviation Certification Turbine Fuel |
ASTM D 7665 : 2017 | Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids |
ASTM D 7752 : 2018 | Standard Practice for Evaluating Compatibility of Mixtures of Hydraulic Fluids |
ASTM D 7863 : 2017 | Standard Guide for Evaluation of Convective Heat Transfer Coefficient of Liquids |
ASTM D 8128 : 2017 | Standard Guide for Monitoring Failure Mode Progression in Industrial Applications with Rolling Element Ball Type Bearings |
ASTM D 8147 : 2017 | Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines |
ASTM D 8185 : 2018 | Standard Guide for In-Service Lubricant Viscosity Measurement |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.