ASTM D 7264/D7264M : 2021
Current
The latest, up-to-date edition.
Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials
Hardcopy , PDF
English
19-02-2021
Committee |
D 30
|
DocumentType |
Test Method
|
Pages |
10
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This test method determines the flexural stiffness and strength properties of polymer matrix composites.
1.1.1Procedure A—A three-point loading system utilizing center loading on a simply supported beam.
1.1.2Procedure B—A four-point loading system utilizing two load points equally spaced from their adjacent support points, with a distance between load points of one-half of the support span.
Note 1:Unlike Test Method D6272, which allows loading at both one-third and one-half of the support span, in order to standardize geometry and simplify calculations, this standard permits loading at only one-half the support span.
1.2For comparison purposes, tests may be conducted according to either test procedure, provided that the same procedure is used for all tests, since the two procedures generally give slightly different property values.
1.3Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 4762 : 2018 | Standard Guide for Testing Polymer Matrix Composite Materials |
ASTM D 7905/D7905M : 2019 : EDT 1 | Standard Test Method for Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
ASTM D 883 : 2024 : REV A | Standard Terminology Relating to Plastics |
ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
ASTM D 3878 : 2023 | Standard Terminology for Composite Materials |
ASTM E 456 : 2013 : REV A : R2022 | Standard Terminology Relating to Quality and Statistics |
ASTM E 456 : 2013 : REV A : R2022 : EDT 1 | Standard Terminology Relating to Quality and Statistics |
ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
ASTM D 2734 : 2023 | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM D 2344/D2344M : 2016 | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates |
ASTM D 2734 : 2016 | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM E 456 : 2013 : REV A : R2017 : EDT 5 | Standard Terminology Relating to Quality and Statistics |
ASTM E 122 : 2017 : R2022 | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
ASTM E 122 : 2017 | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
ASTM D 2344/D2344M : 2022 | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates |
ASTM D 3171 : 2022 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM E 6 : 2015 : EDT 3 | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM D 3878 : 2020 : REV B | Standard Terminology for Composite Materials |
ASTM E 6 : 2023 : REV A | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
ASTM E 6 : 2015 : EDT 4 : REDLINE | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM E 6 : 2015 : EDT 4 | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM D 3171 : 2015 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM E 6 : 2023 | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM E 456 : 2013 : REV A : R2017 : EDT 4 | Standard Terminology Relating to Quality and Statistics |
ASTM E 456 : 2013 : REV A : R2017 : EDT 6 | Standard Terminology Relating to Quality and Statistics |
ASTM E 4 : 2024 | Standard Practices for Force Calibration and Verification of Testing Machines |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.