ASTM D 7518 : 2010 : R2015 : EDT 1
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service
Available format(s)
Hardcopy , PDF
Superseded date
31-07-2020
Superseded by
Language(s)
English
Published date
01-05-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 15.05, 2015 Describes the requirements for 1,3 propanediol base engine coolants used in automobiles or other light-duty service cooling systems.
| Committee |
D 15
|
| DocumentType |
Standard
|
| Pages |
6
|
| ProductNote |
Reconfirmed EDT 1
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the requirements for 1,3 propanediol base engine coolants used in automobiles or other light-duty service cooling systems. When concentrates are used at 40 to 70 % concentration by volume in water, or when prediluted glycol base engine coolants (50 volume % minimum) are used without further dilution, they will function effectively to provide protection against freezing, boiling, and corrosion.
1.2The coolants governed by this specification are categorized as follows:
| Coolant Type | Description |
| I | 1,3 Propanediol base concentrate |
| II | 1,3 Propanediol predilute (50 vol %) |
Note 1:This specification is based on the knowledge of the performance of engine coolants prepared from new or virgin ingredients.
Note 2:This specification applies to automobiles and light-duty service. A specification for heavy-duty engine service is under development.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 2847 : 2015 | Standard Practice for Testing Engine Coolants in Car and Light Truck Service |
| ASTM D 7517 : 2019 | Standard Specification for Fully-Formulated 1,3 Propanediol (PDO) Base Engine Coolant for Heavy-Duty Engines |
| ASTM D 1122 : 2016 | Standard Test Method for Density or Relative Density of Engine Coolant Concentrates and Engine Coolants By The Hydrometer |
| ASTM D 1177 : 2012 | Standard Test Method for Freezing Point of Aqueous Engine Coolants |
| ASTM D 1123 : 1999 : R2009 | Standard Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method |
| ASTM D 5931 : 1996 | Standard Test Method for Density and Relative Density of Engine Coolant Concentrates and Aqueous Engine Coolants by Digital Density Meter |
| ASTM D 1122 : 2016 : R2017 : EDT 1 | Standard Test Method for Density or Relative Density of Engine Coolant Concentrates and Engine Coolants By The Hydrometer |
| ASTM D 1177 : 2017 | Standard Test Method for Freezing Point of Aqueous Engine Coolants |
| ASTM D 3321 : 2019 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
| ASTM D 7388 : 2018 | Standard Specification for Engine Coolant Grade 1,3-Propanediol (PDO) |
| ASTM D 1177 : 2005 | Standard Test Method for Freezing Point of Aqueous Engine Coolants |
| ASTM D 1122 : 2008 | Standard Test Method for Density or Relative Density of Engine Coolant Concentrates and Engine Coolants By The Hydrometer |
| ASTM D 1287 : 2011 : R2020 | Standard Test Method for pH of Engine Coolants and Antirusts |
| ASTM D 1120 : 1994 : R1998 | Standard Test Method for Boiling Point of Engine Coolants |
| ASTM D 1384 : 2001 | Standard Test Method for Corrosion Test for Engine Coolants in Glassware |
| ASTM D 1120 : 2011 | Standard Test Method for Boiling Point of Engine Coolants |
| ASTM D 1287 : 1991 : R1997 : EDT 1 | Standard Test Method for pH of Engine Coolants and Antirusts |
| ASTM D 512 : 2012 | Standard Test Methods for Chloride Ion In Water (Withdrawn 2021) |
| ASTM D 3634 : 1999 : R2009 | Standard Test Method for Trace Chloride Ion in Engine Coolants |
| ASTM D 1287 : 2009 | Standard Test Method for pH of Engine Coolants and Antirusts |
| ASTM D 1177 : 2017 : REDLINE | Standard Test Method for Freezing Point of Aqueous Engine Coolants |
| ASTM D 1122 : 1997 : REV A | Standard Test Method for Density or Relative Density of Engine Coolant Concentrates and Engine Coolants By The Hydrometer |
| ASTM D 1177 : 1994 : R1998 : EDT 1 | Standard Test Method for Freezing Point of Aqueous Engine Coolants |
| ASTM D 4725 : 2011 | Standard Terminology for Engine Coolants |
| ASTM D 1120 : 1994 : R1998 : EDT 1 | Standard Test Method for Boiling Point of Engine Coolants |
| ASTM D 1119 : 2005 : R2015 | Standard Test Method for Percent Ash Content of Engine Coolants |
| ASTM D 1120 : 2008 | Standard Test Method for Boiling Point of Engine Coolants |
| ASTM D 7388 : 2008 : R2013 | Standard Specification for Engine Coolant Grade 1,3-Propanediol (PDO) |
| ASTM D 4340 : 1996 : R2007 | Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions |
| ASTM D 2570 : 1991 | Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants |
| ASTM D 1122 : 2013 | Standard Test Method for Density or Relative Density of Engine Coolant Concentrates and Engine Coolants By The Hydrometer |
| ASTM D 1123 : 1999 : R2003 | Standard Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method |
| ASTM D 1287 : 2011 | Standard Test Method for pH of Engine Coolants and Antirusts |
| ASTM D 3634 : 1999 : R2005 | Standard Test Method for Trace Chloride Ion in Engine Coolants |
| ASTM D 1121 : 2007 | Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts |
| ASTM D 1882 : 1996 | Standard Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles |
| ASTM D 5931 : 1996 : R2002 | Standard Test Method for Density and Relative Density of Engine Coolant Concentrates and Aqueous Engine Coolants by Digital Density Meter |
| ASTM D 2570 : 2016 | Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants |
| ASTM D 1120 : 2017 : REDLINE | Standard Test Method for Boiling Point of Engine Coolants |
| ASTM D 4725 : 1998 | Standard Terminology for Engine Coolants |
| ASTM D 1121 : 2011 : R2020 | Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts |
| ASTM D 1177 : 1994 : R1998 | Standard Test Method for Freezing Point of Aqueous Engine Coolants |
| ASTM D 1882 : 1996 : R2006 | Standard Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles |
| ASTM D 4725 : 2015 : REDLINE | Standard Terminology for Engine Coolants and Related Fluids |
| ASTM D 1121 : 1967 | Standard Method Of Test For Reserve Alkalinity Of Engine Antifreezes And Antirusts |
| ASTM D 2809 : 1994 : R1999 | Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants |
| ASTM D 3321 : 2013 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
| ASTM D 4327 : 2011 | Standard Test Method for Anions in Water by Suppressed Ion Chromatography |
| ASTM D 5827 : 2009 : EDT 1 | Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography |
| ASTM D 1384 : 2005 : EDT 1 | Standard Test Method for Corrosion Test for Engine Coolants in Glassware |
| ASTM D 6660 : 2001 : R2014 : EDT 1 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| ASTM D 6130 : 1997 : REV A : R2009 | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
| ASTM D 1287 : 2011 : REDLINE | Standard Test Method for pH of Engine Coolants and Antirusts |
| ASTM D 1123 : 1999 | Standard Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method |
| ASTM D 6660 : 2001 : R2007 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| ASTM D 3321 : 1994 : R1998 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
| ASTM D 1119 : 2005 : R2009 | Standard Test Method for Percent Ash Content of Engine Coolants |
| ASTM D 1882 : 1996 : R2001 | Standard Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles |
| ASTM D 516 : 2016 : REDLINE | Standard Test Method for Sulfate Ion in Water |
| ASTM D 1123 : 1999 : R2015 | Standard Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method |
| ASTM D 3634 : 1999 : R2005 : EDT 1 | Standard Test Method for Trace Chloride Ion in Engine Coolants |
| ASTM D 1126 : 2002 | Standard Test Method for Hardness in Water |
| ASTM D 6660 : 2001 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| ASTM D 1293 : 1999 | Standard Test Methods for pH of Water |
| ASTM D 1881 : 1997 : R2009 | Standard Test Method for Foaming Tendencies of Engine Coolants in Glassware |
| ASTM D 1881 : 1997 : R2002 : EDT 1 | Standard Test Method for Foaming Tendencies of Engine Coolants in Glassware |
| ASTM D 1120 : 1994 : R2004 | Standard Test Method for Boiling Point of Engine Coolants |
| ASTM D 4327 : 2003 | Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography |
| ASTM D 1121 : 2011 : REDLINE | Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts |
| ASTM D 1882 : 2017 | Standard Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles |
| ASTM D 6130 : 2011 : R2018 | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
| ASTM D 4725 : 2006 | Standard Terminology for Engine Coolants |
| ASTM D 1881 : 2017 | Standard Test Method for Foaming Tendencies of Engine Coolants in Glassware |
| ASTM D 1881 : 1997 : R2002 | Standard Test Method for Foaming Tendencies of Engine Coolants in Glassware |
| ASTM D 1119 : 2005 | Standard Test Method for Percent Ash Content of Engine Coolants |
| ASTM D 1882 : 1996 : R2012 | Standard Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles |
| ASTM D 2809 : 2009 | Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants |
| ASTM D 2570 : 2009 | Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants |
| ASTM D 1123 : 1959 : R1968 | Standard Method Of Test For Water In Concentrated Engine Antifreezes By The Iodine Reagent Method |
| ASTM D 4725 : 2015 | Standard Terminology for Engine Coolants and Related Fluids |
| ASTM D 1119 : 2000 | Standard Test Method for Percent Ash Content of Engine Coolants and Antirusts |
| ASTM D 4340 : 1996 | Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions |
| ASTM E 394 : 2015 : REDLINE | Standard Test Method for Iron in Trace Quantities Using the 1,10-Phenanthroline Method |
| ASTM D 1293 : 1999 : R2005 | Standard Test Methods for pH of Water |
| ASTM D 6130 : 1997 : REV A : R2003 | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
| ASTM D 1121 : 2011 | Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts |
| ASTM D 1384 : 1997 : REV A | Standard Test Method for Corrosion Test for Engine Coolants in Glassware |
| ASTM D 1287 : 1991 : R2002 | Standard Test Method for pH of Engine Coolants and Antirusts |
| ASTM D 1384 : 2004 | Standard Test Method for Corrosion Test for Engine Coolants in Glassware |
| ASTM D 1126 : 2012 | Standard Test Method for Hardness in Water |
| ASTM D 1121 : 1998 | Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts |
| ASTM D 2570 : 2008 | Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants |
| ASTM D 1384 : 2005 : R2019 | Standard Test Method for Corrosion Test for Engine Coolants in Glassware |
| ASTM D 1293 : 2018 | Standard Test Methods for pH of Water |
| ASTM D 4327 : 2017 | Standard Test Method for Anions in Water by Suppressed Ion Chromatography |
| ASTM D 4327 : 1997 | Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography |
| ASTM D 1126 : 2002 : R2007 : EDT 1 | Standard Test Method for Hardness in Water |
| ASTM D 1177 : 2016 | Standard Test Method for Freezing Point of Aqueous Engine Coolants |
| ASTM D 5827 : 1995 | Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography |
| ASTM D 4340 : 2019 | Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions |
| ASTM D 4340 : 1996 : R2001 | Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions |
| ASTM D 6660 : 2001 : R2019 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| ASTM D 1126 : 2017 | Standard Test Method for Hardness in Water |
| ASTM D 4725 : 2004 | Standard Terminology for Engine Coolants |
| ASTM D 2809 : 2009 : R2017 | Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants |
| ASTM D 7388 : 2007 | Standard Specification for Engine Coolant Grade 1,3-Propanediol (PDO) |
| ASTM D 3634 : 1999 : R2015 | Standard Test Method for Trace Chloride Ion in Engine Coolants |
| ASTM D 7388 : 2008 | Standard Specification for Engine Coolant Grade 1,3-Propanediol (PDO) |
| ASTM D 1126 : 1996 | Standard Test Method for Hardness in Water |
| ASTM D 2809 : 2004 : EDT 2 | Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants |
| ASTM D 2809 : 2004 | Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants |
| ASTM D 6130 : 2011 | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
| ASTM D 1120 : 2017 | Standard Test Method for Boiling Point of Engine Coolants |
| ASTM D 4725 : 2008 | Standard Terminology for Engine Coolants |
| ASTM D 3321 : 1994 : R2002 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
| ASTM D 3321 : 2012 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
| ASTM D 1384 : 2005 : R2012 | Standard Test Method for Corrosion Test for Engine Coolants in Glassware |
| ASTM D 5931 : 1996 : R2007 | Standard Test Method for Density and Relative Density of Engine Coolant Concentrates and Aqueous Engine Coolants by Digital Density Meter |
| ASTM D 5827 : 2009 : R2015 | Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography |
| ASTM D 1120 : 2016 | Standard Test Method for Boiling Point of Engine Coolants |
| ASTM D 2809 : 2004 : EDT 1 | Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants |
| ASTM D 1293 : 2012 | Standard Test Methods for pH of Water |
| ASTM D 1122 : 1997 : REV A : R2002 | Standard Test Method for Density or Relative Density of Engine Coolant Concentrates and Engine Coolants By The Hydrometer |
| ASTM D 4725 : 2008 : REV A | Standard Terminology for Engine Coolants |
| ASTM D 1120 : 2011 : EDT 1 | Standard Test Method for Boiling Point of Engine Coolants |
| ASTM D 1384 : 2005 | Standard Test Method for Corrosion Test for Engine Coolants in Glassware |
| ASTM D 1881 : 1997 : R2002 : EDT 2 | Standard Test Method for Foaming Tendencies of Engine Coolants in Glassware |
| ASTM D 2570 : 1996 | Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants |
| ASTM D 5827 : 2009 | Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography |
| ASTM D 4340 : 2010 | Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions |
| ASTM D 2570 : 2016 : REDLINE | Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants |
| ASTM D 1881 : 1997 | Standard Test Method for Foaming Tendencies of Engine Coolants in Glassware |
| ASTM D 2570 : 2010 | Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants |
| ASTM D 1177 : 2007 | Standard Test Method for Freezing Point of Aqueous Engine Coolants |
| ASTM D 3634 : 1999 : EDT 1 | Standard Test Method for Trace Chloride Ion in Engine Coolants |
| ASTM D 1293 : 1984 : R1990 | Standard Test Methods for pH of Water |
| ASTM D 4725 : 2013 | Standard Terminology for Engine Coolants and Related Fluids |
| ASTM D 5931 : 2013 | Standard Test Method for Density and Relative Density of Engine Coolant Concentrates and Aqueous Engine Coolants by Digital Density Meter |
| ASTM D 3321 : 1994 : R2007 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
| ASTM D 6130 : 1997 : REV A | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.