![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 7693/D7693M : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Guide for Application of Heat Weldable Modified Bituminous Waterproofing Membranes Systems for New Concrete Decks
Hardcopy , PDF
17-01-2024
English
31-03-2015
1.1 This guide presents application recommendations for the heat welding installation of multi-ply Styrene Butadiene Styrene (SBS) and Atactic Polypropylene (APP) modified bituminous systems to new, reinforced, cast in place structural concrete used as part of a horizontal waterproofing system over occupied spaces of buildings where covered by a separate wearing course.
Committee |
D 08
|
DocumentType |
Guide
|
Pages |
4
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This guide presents application recommendations for the heat welding installation of multi-ply Styrene Butadiene Styrene (SBS) and Atactic Polypropylene (APP) modified bituminous systems to new, reinforced, cast in place structural concrete used as part of a horizontal waterproofing system over occupied spaces of buildings where covered by a separate wearing course.
1.2For the purpose of this guide, the substrate shall be structurally sound, sloped to drain, able to accept the weight of the membrane and other system materials, and meet the local building code requirements. Similarly, all components of the waterproofing system are assumed to comply with any federal, state, and local environmental regulations that may be in effect at the time of installation. Expansion joints, insulation, drainage layers, filter sheets, overburden, and the wearing surfaces are beyond the scope of this guide.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 1079 : 2018 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 6164 : 2005 : EDT 1 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
ACI 301 : 2016 | SPECIFICATIONS FOR STRUCTURAL CONCRETE |
ASTM D 6163 : 2000 : EDT 1 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements |
ASTM D 6162 : 2000 : REV A | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 1079 : 2008 : REV A | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 6164 : 2005 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
ASTM D 5295 : 2000 | Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems |
ASTM D 1079 : 2016 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2006 | Terminology Relating to Roofing and Waterproofing |
ASTM D 6162 : 2000 : REV A : R2008 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 6162 : 2000 : REV A : EDT 1 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
FM 4470 : 2016 | SINGLE-PLY, POLYMER-MODIFIED BITUMEN SHEET, BUILT-UP ROOF (BUR) AND LIQUID APPLIED ROOF ASSEMBLIES FOR USE IN CLASS 1 AND NONCOMBUSTIBLE ROOF DECK CONSTRUCTION |
ASTM D 1079 : 2020 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 6163 : 2000 : EDT 2 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements |
ASTM D 6222 : 2002 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
ASTM D 6163 : 2000 : R2008 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements |
ASTM D 4586 : 2000 : R2006 | Standard Specification for Asphalt Roof Cement, Asbestos-Free |
ASTM D 4586 : 2000 | Standard Specification for Asphalt Roof Cement, Asbestos-Free |
ASTM D 6163 : 2000 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements |
ASTM D 5957 : 1998 : R2005 | Standard Guide for Flood Testing Horizontal Waterproofing Installations |
ASTM D 6506 : 2001 | Standard Specification for Asphalt Based Protection for Below-Grade Waterproofing |
ASTM D 5295 : 2000 : R2006 | Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems |
ASTM D 1079 : 2013 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2007 : REV A | Terminology Relating to Roofing and Waterproofing |
ASTM D 6223 : 2000 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 1079 : 2010 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 5898 : 1996 | Standard Guide for Standard Details for Adhered Sheet Waterproofing |
ASTM D 6222 : 2002 : EDT 1 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
ASTM D 3019 : 1994 : R2000 : EDT 1 | Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non Fibered, Asbestos Fibered, and Non Asbestos Fibered |
ASTM D 4586 : 2007 | Standard Specification for Asphalt Roof Cement, Asbestos-Free |
ASTM D 1079 : 2018 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 6222 : 2000 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
ASTM D 1079 : 2005 : REV A | Terminology Relating to Roofing and Waterproofing |
ASTM D 3019 : 2008 | Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, Asbestos-Fibered, and Non-Asbestos-Fibered |
ASTM D 5957 : 1998 : R2013 | Standard Guide for Flood Testing Horizontal Waterproofing Installations |
ASTM D 6451 : 1999 | Standard Guide for Application of Asphalt Based Protection Board |
ASTM D 6222 : 2008 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
ASTM D 6223 : 2002 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 1079 : 2002 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM D 5957 : 1998 : R2021 | Standard Guide for Flood Testing Horizontal Waterproofing Installations |
ASTM D 6506 : 2001 : R2009 | Standard Specification for Asphalt Based Protection for Below-Grade Waterproofing |
ASTM D 1079 : 2001 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM D 6223 : 2002 : EDT 1 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 5957 : 1998 | Standard Guide for Flood Testing Horizontal Waterproofing Installations |
ASTM D 5898 : 1996 : R2005 | Standard Guide for Standard Details for Adhered Sheet Waterproofing |
ASTM D 6223 : 2000 : EDT 1 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 6164 : 2000 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
ASTM D 41 : 2005 | Standard Specification for Asphalt Primer Used in Roofing, Dampproofing, and Waterproofing |
ASTM D 1079 : 2000 : REV A | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM D 6222 : 2000 : EDT 1 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
ASTM D 6223 : 2002 : EDT 2 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 1079 : 2013 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2009 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 6222 : 2002 : EDT 2 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.