![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 7715 : 2012 : R2016 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Fully-Formulated Glycerin Base Engine Coolant for Heavy-Duty Engines
Hardcopy , PDF
16-09-2021
English
27-05-2020
CONTAINED IN VOL. 15.05, 2016 Describes the requirements for fully-formulated glycerin base coolants for cooling systems of heavy-duty engines.
Committee |
D 15
|
DocumentType |
Standard
|
Pages |
5
|
ProductNote |
Reconfirmed EDT 1
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers the requirements for fully-formulated glycerin base coolants for cooling systems of heavy-duty engines. When concentrates are used at 40 to 60 % glycerin concentration by volume in water of suitable quality (see Appendix X1), or when prediluted glycerin base engine coolants (50 volume % min) are used without further dilution, they will function effectively during both winter and summer to provide protection against corrosion, cavitation, freezing, and boiling.
1.2This specification is intended to cover the requirements for engine coolants prepared from virgin glycerin.
Note 1:This specification is based on the knowledge of the performance of engine coolants prepared from new or virgin ingredients that comply with Specification D7714.
1.3The coolants governed by this specification are categorized as follows:
Coolant Type | Description |
V-FF | Glycerin base concentrate |
VI-FF | Glycerin predilute (50 vol %) |
1.4Coolant concentrates meeting this specification do not require addition of supplemental coolant additive (SCA) until the first maintenance interval when a maintenance dose of SCA is required to continue protection in certain heavy duty engine cooling systems, particularly those of the wet cylinder liner-in-block design. The SCA additions are defined by and are the primary responsibility of the engine manufacturer or vehicle manufacturer. If they provide no instructions, follow the SCA supplier's instructions.
1.5The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 2847 : 2015 | Standard Practice for Testing Engine Coolants in Car and Light Truck Service |
ASTM D 3321 : 2019 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
ASTM D 3306 : 2014 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 5828 : 1997 : R2011 : EDT 1 | Standard Test Method for Compatibility of Supplemental Coolant Additives (SCAs) and Engine Coolant Concentrates |
ASTM D 4725 : 2011 | Standard Terminology for Engine Coolants |
ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
ASTM D 3306 : 2003 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 3306 : 2009 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 4725 : 1998 | Standard Terminology for Engine Coolants |
ASTM D 3306 : 2014-05 | SPECIFICATION FOR GLYCOL BASE ENGINE COOLANT FOR AUTOMOBILE AND LIGHT-DUTY SERVICE |
ASTM D 4725 : 2015 : REDLINE | Standard Terminology for Engine Coolants and Related Fluids |
ASTM D 3321 : 2013 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
ASTM D 4327 : 2011 | Standard Test Method for Anions in Water by Suppressed Ion Chromatography |
ASTM D 6130 : 1997 : REV A : R2009 | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
ASTM D 7714 : 2011 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 7583 : 2009 | Standard Test Method for John Deere Coolant Cavitation Test |
ASTM D 3321 : 1994 : R1998 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
ASTM D 5828 : 1997 | Standard Test Method for Compatibility of Supplemental Coolant Additives (SCAs) and Engine Coolant Concentrates |
ASTM D 3306 : 2010 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 7583 : 2016 | Standard Test Method for John Deere Coolant Cavitation Test |
ASTM D 1126 : 2002 | Standard Test Method for Hardness in Water |
ASTM D 7583 : 2016 : REDLINE | Standard Test Method for John Deere Coolant Cavitation Test |
ASTM D 1293 : 1999 | Standard Test Methods for pH of Water |
ASTM D 5828 : 1997 : R2018 | Standard Test Method for Compatibility of Supplemental Coolant Additives (SCAs) and Engine Coolant Concentrates |
ASTM D 4327 : 2003 | Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography |
ASTM D 3306 : 2008 : REV A | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 6130 : 2011 : R2018 | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
ASTM D 4725 : 2006 | Standard Terminology for Engine Coolants |
ASTM D 4725 : 2015 | Standard Terminology for Engine Coolants and Related Fluids |
ASTM D 3306 : 2001 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 1293 : 1999 : R2005 | Standard Test Methods for pH of Water |
ASTM D 6130 : 1997 : REV A : R2003 | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
ASTM D 1126 : 2012 | Standard Test Method for Hardness in Water |
ASTM D 1293 : 2018 | Standard Test Methods for pH of Water |
ASTM D 4327 : 2017 | Standard Test Method for Anions in Water by Suppressed Ion Chromatography |
ASTM D 7714 : 2011 : R2016 : EDT 1 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 4327 : 1997 | Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography |
ASTM D 1126 : 2002 : R2007 : EDT 1 | Standard Test Method for Hardness in Water |
ASTM D 1126 : 2017 | Standard Test Method for Hardness in Water |
ASTM D 4725 : 2004 | Standard Terminology for Engine Coolants |
ASTM D 1126 : 1996 | Standard Test Method for Hardness in Water |
ASTM D 3306 : 2005 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 6130 : 2011 | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
ASTM D 4725 : 2008 | Standard Terminology for Engine Coolants |
ASTM D 3321 : 1994 : R2002 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
ASTM D 3321 : 2012 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
ASTM D 1293 : 2012 | Standard Test Methods for pH of Water |
ASTM D 3306 : 2019 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 4725 : 2008 : REV A | Standard Terminology for Engine Coolants |
ASTM D 3306 : 2000 : REV A | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 5828 : 1997 : R2002 | Standard Test Method for Compatibility of Supplemental Coolant Additives (SCAs) and Engine Coolant Concentrates |
ASTM D 3306 : 2008 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 3306 : 2011 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 1293 : 1984 : R1990 | Standard Test Methods for pH of Water |
ASTM D 4725 : 2013 | Standard Terminology for Engine Coolants and Related Fluids |
ASTM D 3321 : 1994 : R2007 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
ASTM D 6130 : 1997 : REV A | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.