• Shopping Cart
    There are no items in your cart

ASTM D 7774 : 2017

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Flexural Fatigue Properties of Plastics

Available format(s)

Hardcopy , PDF

Superseded date

25-07-2022

Superseded by

ASTM D 7774 : 2022

Language(s)

English

Published date

12-03-2018

€67.30
Excluding VAT

This test method covers the determination of dynamic full reversed fatigue properties of plastics in flexure.

Committee
D 20
DocumentType
Test Method
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This test method covers the determination of dynamic full reversed fatigue properties of plastics in flexure. This method is applicable to rigid and semi-rigid plastics. Stress and strain levels are below the proportional limit of the material where the strains and stresses are relatively elastic. Three-point or four-point bending systems are used to determine these properties.

1.2This test method can be used with two procedures:

1.2.1Procedure A, designed for materials that use three-point loading systems to determine flexural strength. Three-point loading system is used for this procedure.

1.2.2Procedure B, designed for materials that use four-point loading systems to determine flexural strength. Four-point loading system is used for this procedure.

1.3Comparative tests can be run in accordance with either procedure, provided that the procedure is found satisfactory for the material being tested.

1.4The values stated in SI units are to be regarded as the standard. The values provided in parentheses are for information only.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:This standard and ISO 13003 address the same subject matter, but differ in technical content and results cannot be directly compared between the two test methods.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM E 1942 : 1998 : R2010 Standard Guide for Evaluating Data Acquisition Systems Used in Cyclic Fatigue and Fracture Mechanics Testing
ASTM D 5947 : 1996 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 2839 : 2016 Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
ASTM D 6272 : 2010 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM E 83 : 2000 : EDT 1 Standard Practice for Verification and Classification of Extensometer
ASTM D 5947 : 2002 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM E 83 : 1998 : EDT 1 Standard Practice for Verification and Classification of Extensometer
ASTM D 5947 : 2011 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 4883 : 2003 Standard Test Method for Density of Polyethylene by the Ultrasound Technique
ASTM D 5947 : 2018 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM E 1942 : 1998 : EDT 1 Standard Guide for Evaluating Data Acquisition Systems Used in Cyclic Fatigue and Fracture Mechanics Testing
ASTM D 1505 : 2003 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 2839 : 1996 Standard Test Method for Use of a Melt Index Strand for Determining Density of Polyethylene
ASTM D 6272 : 2017 : EDT 1 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 5947 : 2006 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 6272 : 2017 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 1505 : 1968 : R1979 Standard Test Method for Density Of Plastics By The Density-Gradient Technique
ASTM E 1942 : 1998 : R2018 : EDT 1 Standard Guide for Evaluating Data Acquisition Systems Used in Cyclic Fatigue and Fracture Mechanics Testing
ASTM D 6272 : 2002 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 6272 : 2002 : R2008 : EDT 1 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 2839 : 2010 Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM E 4 : 2021 Standard Practices for Force Calibration and Verification of Testing Machines
ASTM D 2839 : 2005 Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
ASTM D 5947 : 2003 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 5947 : 2001 : EDT 1 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 1505 : 2010 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 1505 : 2018 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 1505 : 1998 : EDT 1 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 4883 : 2008 Standard Test Method for Density of Polyethylene by the Ultrasound Technique (Withdrawn 2017)
ASTM D 4883 : 1999 Standard Test Method for Density of Polyethylene by the Ultrasound Technique
ASTM D 6272 : 2000 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM E 1942 : 1998 : R2010 : EDT 1 Standard Guide for Evaluating Data Acquisition Systems Used in Cyclic Fatigue and Fracture Mechanics Testing
ASTM D 2839 : 2002 Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM E 1942 : 1998 : R2004 Standard Guide for Evaluating Data Acquisition Systems Used in Cyclic Fatigue and Fracture Mechanics Testing
ASTM D 4883 : 2018 Standard Test Method for Density of Polyethylene by the Ultrasound Technique

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.