![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 7793 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Insulated Vinyl Siding
Hardcopy , PDF
14-12-2020
English
19-07-2017
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
14
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification establishes requirements for insulated vinyl siding, which is vinyl siding with integral foam plastic insulating material, where the vinyl siding is manufactured from rigid PVC compound. Compliance with this standard requires insulated vinyl siding to demonstrate a thermal insulation value of R-2.0 or greater. Other performance requirements and test methods addressed by this standard include materials properties and dimensions, warp, shrinkage, impact strength, expansion, appearance, thermal distortion resistance, and windload resistance. Methods of indicating compliance with this specification are also provided.
Note 1:Insulated vinyl siding is composed of two major components: the vinyl siding and the insulating material. It is intended that the vinyl siding portion comply with Specification D3679. Applicable portions of Specification D3679 are included in this specification. Additional requirements that pertain only to the insulation as a separate material, or to the combination of vinyl siding and insulation as a whole, are also included. For further explanation, see Appendix X1.
1.2Insulated vinyl siding shall be tested with the insulation material in place or removed, as specified in the applicable requirement or test method.
1.3The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.
1.4Insulated vinyl siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer's installation instructions for the specific product to be installed.
1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 2:There is no known ISO equivalent to this standard.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7445 : 2018 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding) |
ASTM C 1199 : 2009 : EDT 1 | Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods |
ASTM D 7445 : 2017 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding) |
ASTM C 1289 : 2015 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C 1289 : 2011 : REV A | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C 1289 : 2014 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 5947 : 1996 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 1435 : 2013 | Standard Practice for Outdoor Weathering of Plastics |
ASTM D 3679 : 2006 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
ASTM C 1289 : 2016 : REV A | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM E 1753 : 2001 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 4226 : 2005 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 2244 : 2015 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM C 1289 : 2012 : REV A | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 4756 : 2002 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM E 1753 : 1995 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 5947 : 2002 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM E 1753 : 2019 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM C 1363 : 2019 | Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus |
ASTM D 4756 : 2013 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 7445 : 2009 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding) |
ASTM D 2244 : 2011 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 2457 : 2008 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM D 4226 : 2019 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
ASTM C 1363 : 2005 | Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus |
ASTM C 1363 : 1997 | Standard Test Method for the Thermal Performance of Building Assemblies by Means of a Hot Box Apparatus |
ASTM D 2244 : 2009 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 5206 : 2019 | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
ASTM D 4756 : 1996 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 1042 : 2006 | Standard Test Method for Linear Dimensional Changes of Plastics Under Accelerated Service Conditions |
ASTM C 1289 : 2008 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 7209 : 2006 | Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015) |
ASTM D 5947 : 2011 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 5947 : 2018 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 2244 : 2002 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 1183 : 2003 : R2019 | Standard Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions |
ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 3679 : 2003 : EDT 2 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3679 : 2008 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM E 1753 : 2018 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 4756 : 2015 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 2244 : 2015 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 2244 : 2009 : REV B | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 1042 : 1993 | Standard Test Method for Linear Dimensional Changes of Plastics Under Accelerated Service Conditions |
ASTM D 2244 : 2002 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM C 1289 : 2006 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 3679 : 2001 : REV B | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 2244 : 2015 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM E 1753 : 2018 : REV A | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 3679 : 2002 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3679 : 2009 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1435 : 1994 | Standard Practice for Outdoor Weathering of Plastics |
ASTM D 3679 : 2004 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1183 : 1996 : EDT 1 | Standard Test Methods for Resistance of Adhesives to Cyclic Laboratory Aging Conditions |
ASTM C 1289 : 2008 : EDT 1 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM E 1753 : 2013 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 5947 : 2006 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM C 1289 : 2005 : REV A | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C 1289 : 2007 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 1042 : 2001 : REV A | Standard Test Method for Linear Dimensional Changes of Plastics Under Accelerated Service Conditions |
ASTM D 2457 : 2013 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM C 1289 : 2012 : EDT 1 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C 1289 : 2014 : REV A | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 5206 : 2006 : REV A | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
ASTM D 2244 : 2014 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 7445 : 2018 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding) |
ASTM D 3679 : 2004 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3679 : 2009 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 2244 : 2005 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM C 1199 : 2014 | Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods |
ASTM D 1042 : 2012 : R2017 | Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture |
ASTM C 1289 : 2005 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 4756 : 2003 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 3679 : 2017 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM C 1363 : 2011 | Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus |
ASTM D 3679 : 2013 | Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding |
ASTM C 1199 : 2000 | Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods |
ASTM D 4226 : 2010 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 1183 : 2003 | Standard Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions |
ASTM D 3679 : 2011 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM C 1289 : 2001 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 1435 : 2005 | Standard Practice for Outdoor Weathering of Plastics |
ASTM C 1289 : 2013 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C 1199 : 2000 : R2008 | Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods |
ASTM D 3679 : 1999 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM C 1289 : 2002 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 2457 : 1997 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM D 3679 : 2003 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 2244 : 2007 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 5947 : 2003 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 1042 : 2001 | Standard Test Method for Linear Dimensional Changes of Plastics Under Accelerated Service Conditions |
ASTM C 1289 : 2010 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 4226 : 2016 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 3679 : 2004 : REV A : EDT 1 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM C 1289 : 2016 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 3679 : 2005 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM C 1289 : 2018 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C 1289 : 2012 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C 1289 : 2004 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 3679 : 2002 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 4756 : 2002 : REV A | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 5206 : 1996 | Standard Test Method for Windload Resistance of Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 4226 : 2000 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 5206 : 2013 | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
ASTM D 1183 : 2003 : R2011 | Standard Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions |
ASTM D 4756 : 2006 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 2457 : 2003 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM C 1289 : 2013 : EDT 1 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 2244 : 2009 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM C 1289 : 2011 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 2244 : 1993 : R2000 | Standard Test Method for Calculation of Color Differences From Instrumentally Measured Color Coordinates |
ASTM D 3679 : 2001 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM C 1289 : 2017 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 3679 : 2003 : EDT 1 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM E 1753 : 2004 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 2457 : 2008 : EDT 1 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM D 3679 : 2001 : REV C | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1042 : 2012 | Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture |
ASTM C 1199 : 2009 | Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods |
ASTM C 1289 : 2003 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C 1289 : 1998 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM D 4226 : 2009 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 3679 : 2001 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1435 : 1999 | Standard Practice for Outdoor Weathering of Plastics |
ASTM D 4226 : 2011 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 3679 : 2006 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM C 1199 : 2012 | Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods |
ASTM C 1289 : 2018 : REV A | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.