ASTM D 7793 : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Insulated Vinyl Siding
Hardcopy , PDF
24-04-2024
English
14-12-2020
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
14
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification establishes requirements for insulated vinyl siding, which is vinyl siding with integral foam plastic insulating material, where the vinyl siding is manufactured from rigid PVC compound. Compliance with this standard requires insulated vinyl siding to demonstrate a thermal insulation value of R-2.0 or greater. Other performance requirements and test methods addressed by this standard include materials properties and dimensions, warp, shrinkage, impact strength, expansion, appearance, thermal distortion resistance, flame spread, and windload resistance. Methods of indicating compliance with this specification are also provided.
Note 1:Insulated vinyl siding is composed of two major components: the vinyl siding and the insulating material. It is intended that the vinyl siding portion comply with Specification D3679. Applicable portions of Specification D3679 are included in this specification. Additional requirements that pertain only to the insulation as a separate material, or to the combination of vinyl siding and insulation as a whole, are also included. For further explanation, see Appendix X1.
1.2Insulated vinyl siding shall be tested with the insulation material in place or removed, as specified in the applicable requirement or test method.
1.3The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.
1.4Insulated vinyl siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer's installation instructions for the specific product to be installed.
1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2:There is no known ISO equivalent to this standard.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7445 : 2018 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding) |
ASTM D 2244 : 2021 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 5206 : 1996 : R2002 : EDT 1 | Standard Test Method for Windload Resistance of Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 1183 : 2003 : R2019 | Standard Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions |
ASTM C 591 : 2020 | Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation |
ASTM E 84 : 2021 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 2457 : 2013 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM E 84 : 2020 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 3679 : 2004 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3679 : 2017 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 3679 : 2021 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 5947 : 2001 : EDT 1 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM C 1289 : 2020 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C 1289 : 2021 | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
ASTM C 591 : 2021 | Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation |
ASTM D 2457 : 2021 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.