ASTM D 7826 : 2021
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives
Hardcopy , PDF
07-06-2023
English
12-01-2022
Committee |
D 02
|
DocumentType |
Guide
|
Pages |
27
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This guide provides procedures to develop data for use in research reports for new aviation gasolines or new aviation gasoline additives.
1.2This data is intended to be used by the ASTM subcommittee to make a determination of the suitability of the fuel for use as an aviation fuel in either a fleet-wide or limited capacity, and to make a determination that the proposed properties and criteria in the associated standard specification provide the necessary controls to ensure this fuel maintains this suitability during high-volume production.
1.3These research reports are intended to support the development and issuance of new specifications or specification revisions for these products. Guidance to develop ASTM International standard specifications for aviation gasoline is provided in Subcommittee J on Aviation Fuels Operating Procedures, Annex A6, “Guidelines for the Development and Acceptance of a New Aviation Fuel Specification for Spark-Ignition Reciprocating Engines.”
1.4The procedures, tests, selection of materials, engines, and aircraft detailed in this guide are based on industry expertise to give appropriate data for review. Because of the diversity of aviation hardware and potential variation in fuel/additive formulations, not every aspect may be encompassed and further work may be required. Therefore, additional data beyond that described in this guide may be requested by the ASTM task force, Subcommittee J, or Committee D02 upon review of the specific composition, performance, or other characteristics of the candidate fuel or additive.
1.5While it is beyond the scope of this guide, investigation of the future health and environmental impacts of the new aviation gasoline or new aviation gasoline additive and the requirements of environmental agencies is recommended.
1.6The values stated in SI units are to be regarded as standard.
1.6.1Exception—Some industry standard methodologies utilize imperial units as their primary system (permeability; Table A2.2).
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7719 : 2021 : REV A | Standard Specification for High Aromatic Content Unleaded Hydrocarbon Aviation Gasoline Test Fuel |
ASTM D 7960 : 2021 | Standard Specification for Unleaded Aviation Gasoline Test Fuel Containing Non-hydrocarbon Components |
ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 4865 : 2019 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
ASTM D 5191 : 2022 | Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method) |
ASTM D 6812 : 2004 : REV A : R2019 | Standard Practice for Ground-Based Octane Rating Procedures for Turbocharged/Supercharged Spark Ignition Aircraft Engines |
ASTM D 2583 : 2013 : REV A | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor (Withdrawn 2022) |
ASTM D 873 : 2022 | Standard Test Method for Oxidation Stability of Aviation Fuels (Potential Residue Method) |
ASTM D 7719 : 2021 : REV A | Standard Specification for High Aromatic Content Unleaded Hydrocarbon Aviation Gasoline Test Fuel |
ASTM D 7220 : 2012 : R2017 | Standard Test Method for Sulfur in Automotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 909 : 2021 | Standard Test Method for Supercharge Rating of Spark-Ignition Aviation Gasoline |
ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 1414 : 2022 | Standard Test Methods for Rubber O-Rings |
ASTM D 6227 : 2018 | Standard Specification for Unleaded Aviation Gasoline Containing a Non-hydrocarbon Component |
ASTM D 445 : 2021 : EDT 2 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
ASTM D 2700 : 2022 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2344/D2344M : 2016 | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates |
ASTM D 6424 : 2004 : REV A : R2019 | Standard Practice for Octane Rating Naturally Aspirated Spark Ignition Aircraft Engines |
ASTM D 2624 : 2021 : REV A | Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels |
ASTM D 909 : 2022 | Standard Test Method for Supercharge Rating of Spark-Ignition Aviation Gasoline |
ASTM D 2344/D2344M : 2022 | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates |
ASTM D 7547 : 2021 | Standard Specification for Hydrocarbon Unleaded Aviation Gasoline |
ASTM D 3359 : 2022 | Standard Test Methods for Rating Adhesion by Tape Test |
ASTM D 1500 : 2012 : R2017 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM D 910 : 2021 | Standard Specification for Leaded Aviation Gasolines |
ASTM D 97 : 2017 : REV B | Standard Test Method for Pour Point of Petroleum Products |
ASTM D 2700 : 2021 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7220 : 2022 | Standard Test Method for Sulfur in Automotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 381 : 2019 | Standard Test Method for Gum Content in Fuels by Jet Evaporation |
ASTM D 381 : 2022 | Standard Test Method for Gum Content in Fuels by Jet Evaporation |
ASTM D 4294 : 2021 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 2622 : 2021 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 97 : 2017 : REV B : R2022 | Standard Test Method for Pour Point of Petroleum Products |
ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 2700 : 2022 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4052 : 2022 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 7042 : 2021 : REV A | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
ASTM D 5191 : 2020 | Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method) |
ASTM D 4308 : 2021 | Standard Test Method for Electrical Conductivity of Liquid Hydrocarbons by Precision Meter |
ASTM D 445 : 2021 : EDT 1 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
ASTM D 3359 : 2017 | Standard Test Methods for Rating Adhesion by Tape Test |
ASTM D 1094 : 2007 : R2019 | Standard Test Method for Water Reaction of Aviation Fuels |
ASTM D 2896 : 2021 | Standard Test Method for Base Number of Petroleum Products by Potentiometric Perchloric Acid Titration |
ASTM D 2624 : 2022 | Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels |
ASTM D 873 : 2012 : R2018 | Standard Test Method for Oxidation Stability of Aviation Fuels (Potential Residue Method) |
ASTM D 1414 : 2015 | Standard Test Methods for Rubber O-Rings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.