ASTM D 7891 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Shear Testing of Powders Using the Freeman Technology FT4 Powder Rheometer Shear Cell
Hardcopy , PDF
24-04-2024
English
20-03-2015
CONTAINED IN VOL. 04.09, 2015 Defines the apparatus and procedures for measuring the incipient failure properties of a powder as a function of the normal stress for a given level of consolidation.
Committee |
D 18
|
DocumentType |
Test Method
|
Pages |
11
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This method covers the apparatus and procedures for measuring the incipient failure properties of a powder as a function of the normal stress for a given level of consolidation. The method also allows the further determination of the unconfined yield strength, internal friction angles, cohesion, flow function, major principal stress and wall friction angle (with the appropriate wall coupon fitted to the correct accessory).
1.2These parameters are most commonly used for the design of storage hoppers and bins using industry standard calculations and procedures. They can also provide relative classification or comparison of the flow behavior of different powders or different batches of the same powder if similar stress and shear regimes are encountered within the processing equipment.
1.3The apparatus is suitable for measuring the properties of powders with a maximum particle size of 1 mm. It is possible to test powders which have a small proportion of particles of 1 mm or greater, but they should be present in the bulk sample as no more than 5 % of the total mass in samples with a normal (Gaussian) size distribution.
1.4All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.4.1The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.
1.5Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 8081 : 2017 | Standard Guide for Theory and Principles for Obtaining Reliable and Accurate Bulk Solids Flow Data Using a Direct Shear Cell |
ASTM D 8081 : 2017 : R2021 : EDT 1 | Standard Guide for Theory and Principles for Obtaining Reliable and Accurate Bulk Solids Flow Data Using a Direct Shear Cell |
ASTM D 2216 : 2005 | Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
ASTM D 6128 : 1997 | Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Cell |
ASTM D 6128 : 2022 | Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Tester |
ASTM D 653 : 2007 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
ASTM D 2216 : 2010 | Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
ASTM D 3740 : 2012 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 6773 : 2016 : REDLINE | Standard Test Method for Bulk Solids Using Schulze Ring Shear Tester |
ASTM D 3740 : 2023 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 6128 : 2006 | Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Cell |
ASTM D 3740 : 2019 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 3740 : 2004 : REV A : EDT 1 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 6128 : 2014 | Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Cell |
ASTM D 6773 : 2002 | Standard Shear Test Method for Bulk Solids Using the Schulze Ring Shear Tester |
ASTM D 3740 : 2008 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 6026 : 2013 | Standard Practice for Using Significant Digits in Geotechnical Data |
ASTM D 6682 : 2001 | Standard Test Method for Measuring the Shear Stresses of Powders Using the Peschl Rotational Split Level Shear Tester |
ASTM D 3740 : 2012-06 | PRACTICE FOR MINIMUM REQUIREMENTS FOR AGENCIES ENGAGED IN TESTING AND/OR INSPECTION OF SOIL AND ROCK AS USED IN ENGINEERING DESIGN AND CONSTRUCTION |
ASTM D 6026 : 2006 | Standard Practice for Using Significant Digits in Geotechnical Data |
ASTM D 3740 : 1999 : REV C | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 6128 : 2016 : REDLINE | Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Tester |
ASTM D 653 : 2022 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
ASTM D 6128 : 2000 | Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Cell |
ASTM D 6773 : 2008 | Standard Shear Test Method for Bulk Solids Using the Schulze Ring Shear Tester |
ASTM D 653 : 2020 : EDT 1 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
ASTM D 6026 : 1999 | Standard Practice for Using Significant Digits in Geotechnical Data |
ASTM D 3740 : 2011 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 6773 : 2016 | Standard Test Method for Bulk Solids Using Schulze Ring Shear Tester |
ASTM D 6026 : 2001 : EDT 1 | Standard Practice for Using Significant Digits in Geotechnical Data |
ASTM D 3740 : 2010 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 653 : 2021 : REV A | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
ASTM D 2216 : 2019 | Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
ASTM D 6026 : 1996 | Standard Practice for Using Significant Digits in Geotechnical Data |
ASTM D 3740 : 2004 : REV A | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 3740 : 2001 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 653 : 2021 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
ASTM D 653 : 2021 : REV B | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
ASTM D 6682 : 2008 | Standard Test Method for Measuring Shear Stresses of Powders Using Peschl Rotational Split Level Shear Tester (Withdrawn 2017) |
ASTM D 6773 : 2022 | Standard Test Method for Bulk Solids Using Schulze Ring Shear Tester |
ASTM D 6682 : 2001 : R2006 | Standard Test Method for Measuring Shear Stresses of Powders Using Peschl Rotational Split Level Shear Tester |
ASTM D 6026 : 1996 : EDT 1 | Standard Practice for Using Significant Digits in Geotechnical Data |
ASTM D 3740 : 2012 : REV A | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 3740 : 2003 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 2216 : 1998 | Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
ASTM D 6026 : 2021 | Standard Practice for Using Significant Digits and Data Records in Geotechnical Data |
ASTM D 2216 : 1971 | Standard Method of Laboratory Determination Of Moisture Content Of Soil |
ASTM D 6026 : 2001 | Standard Practice for Using Significant Digits in Geotechnical Data |
ASTM D 6128 : 2016 | Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Tester |
ASTM D 6026 : 2013 : REDLINE | Standard Practice for Using Significant Digits in Geotechnical Data |
ASTM D 3740 : 2004 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
ASTM D 653 : 2014 : REDLINE | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.