ASTM D 8003 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determination of Light Hydrocarbons and Cut Point Intervals in Live Crude Oils and Condensates by Gas Chromatography
Hardcopy , PDF
11-03-2021
English
01-06-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 05.04, 2017 Describes the determination of light hydrocarbons and cut point intervals by gas chromatography in live crude oils and condensates with VPCR[4] up to 500 kPa at 37.8 degrees C.
| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
15
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers the determination of light hydrocarbons and cut point intervals by gas chromatography in live crude oils and condensates with VPCR4 (see Note 1) up to 500 kPa at 37.8 °C.
Note 1:As described in Test Method D6377.
1.2Methane (C1) to hexane (nC6) and benzene are speciated and quantitated. Samples containing mass fractions of up to 0.5 % methane, 2.0 % ethane, 10 % propane, or 15 % isobutane may be analyzed. A mass fraction with a lower limit of 0.001 % exists for these compounds.
1.3This test method may be used for the determination of cut point carbon fraction intervals (see 3.1.2) of live crude oils and condensates from initial boiling point (IBP) to 391 °C (nC24). The nC24 plus fraction is reported.
1.4Dead oils or condensates sampled in accordance with 12.1 may also be analyzed.
1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5.1Exception—Where there is no direct SI equivalent such as tubing size.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 8236 : 2018 | Standard Practice for Preparing an Equilibrium Liquid/Vapor Sample of Live Crude Oil, Condensates, or Liquid Petroleum Products Using a Manual Piston Cylinder for Subsequent Liquid Analysis or Gas Analysis |
| ASTM D 3700 : 2016 : REDLINE | Standard Practice for Obtaining LPG Samples Using a Floating Piston Cylinder |
| ASTM D 6792 : 2017 : REDLINE | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 6377 : 2016 : REDLINE | Standard Test Method for Determination of Vapor Pressure of Crude Oil: VPCR<inf>x</inf > (Expansion Method) |
| CGSB 3.0-14.3 : 2016 | METHODS OF TESTING PETROLEUM AND ASSOCIATED PRODUCTS - STANDARD TEST METHOD FOR THE IDENTIFICATION OF HYDROCARBON COMPONENTS IN AUTOMATIVE GASOLINE USING GAS CHROMATOGRAPHY |
| ASTM D 4307 : 2017 : REDLINE | Standard Practice for Preparation of Liquid Blends for Use as Analytical Standards |
| ASTM D 5002 : 2016-02 | TEST METHOD FOR DENSITY AND RELATIVE DENSITY OF CRUDE OILS BY DIGITAL DENSITY ANALYZER |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.