ASTM D 8111 : 2019
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine
Available format(s)
Hardcopy , PDF
Superseded date
15-11-2019
Superseded by
Language(s)
English
Published date
01-05-2019
Important note : Users cannot be edited or removed once added to your Multi user PDF.This test method covers an engine test procedure for evaluating automotive engine oils for certain high-temperature performance characteristics, including oil thickening (as measured by kinematic viscosity increase), piston deposits, ring sticking, oil consumption, and phosphorus retention.
| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
38
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers an engine test procedure for evaluating automotive engine oils for certain high-temperature performance characteristics, including oil thickening (as measured by kinematic viscosity increase), piston deposits, ring sticking, oil consumption, and phosphorus retention. Such oils include both single-viscosity and multiviscosity grade oils that are used in both spark-ignition, gasoline-fueled engines, as well as in diesel engines.
1.1.1Additionally, with nonmandatory supplemental requirements, a Sequence IIIHA Test (Mini Rotary Viscometer and Cold Cranking Simulator measurements), or a Sequence IIIHB Test (phosphorus retention measurement) can be conducted. These supplemental test procedures are contained in Appendix X1 and Appendix X2, respectively.
Note 1:Companion test methods used to evaluate engine oil performance for specification requirements are discussed in SAE J304.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1Exceptions:
1.2.1.1Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing sizes, and valve sizes and springs.
1.2.1.2The ring end gaps in Table A8.7, the dimensions for the blowby ventilation support bracket in Fig. A3.2, and the torque wrenches in Table A8.1 are in inch-pound units.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are provided in 6.11.6, 7.1, 7.2.1, and 7.3.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7320 : 2011 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 4175 : 2014 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4485 : 2003 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 4175 : 2009 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2699 : 2016 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4684 : 2002 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 2699 : 2011 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 3338 : 1992 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| ASTM D 4175 : 2008 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5453 : 2009 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 3343 : 2005 : R2010 | Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels |
| ASTM D 4485 : 2006 | Standard Specification for Performance of Engine Oils |
| ASTM D 4175 : 2005 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4485 : 2011 : REV C | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 2699 : 1999 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 1319 : 1989 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Absorption |
| ASTM D 4175 : 2005 : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1319 : 2008 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 2700 : 2009 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2700 : 2018 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2699 : 2004 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2700 : 2011 : EDT 1 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4485 : 2001 | Standard Specification for Performance of Engine Oils |
| ASTM D 5453 : 2008 : REV B | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 2699 : 2007 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 3244 : 1997 | Standard Practice for Utilization of Test Data to Determine Conformance with Specifications |
| ASTM D 5453 : 2000 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 2700 : 2007 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 3231 : 1999 | Standard Test Method for Phosphorus in Gasoline |
| ASTM D 2699 : 2013 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5185 : 1997 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4175 : 2015 : REV C | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 3231 : 2013 | Standard Test Method for Phosphorus in Gasoline |
| ASTM D 3244 : 2012 | Standard Practice for Utilization of Test Data to Determine Conformance with Specifications |
| ASTM D 4815 : 2015 : REV B | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
| ASTM D 5191 : 2018 : REV A | Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method) |
| ASTM D 4175 : 2017 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2699 : 2017 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4485 : 2003 | Standard Specification for Performance of Engine Oils |
| ASTM D 4052 : 1996 : R2002 : EDT 1 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
| ASTM D 4485 : 2008 | Standard Specification for Performance of Engine Oils |
| ASTM D 4739 : 2005 | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 4485 : 2015 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 5453 : 2004 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 1319 : 2018 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4485 : 2005 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 2700 : 2014 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4684 : 2008 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 2700 : 2009 : EDT 1 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2700 : 2007 : REV B | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4175 : 2008 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5453 : 2012 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 1319 : 2014 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4175 : 2017 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2009 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4485 : 2011 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 3244 : 2007 | Standard Practice for Utilization of Test Data to Determine Conformance with Specifications |
| ASTM D 5293 : 2010 : EDT 1 | Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between <span class='unicode'>–</span>5 and <span class='unicode'>–</span>35<span class='unicode'>°</span>C Using Cold-Cranking Simulator |
| ASTM D 3338 : 2000 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| ASTM D 5191 : 2006 : EDT 1 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 2700 : 2013 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 3338 : 2004 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| ASTM D 3343 : 2005 | Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels |
| ASTM D 2699 : 1992 | Standard Test Method for Knock Characteristics of Motor Fuels by the Research Method |
| ASTM D 7320 : 2014 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 3237 : 2006 : EDT 1 | Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy |
| ASTM D 1319 : 1999 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 2700 : 2010 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4485 : 2018 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 5185 : 2005 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 2700 : 2003 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2700 : 1992 | Standard Test Method for Knock Characteristics of Motor and Aviation Fuels by the Motor Method |
| ASTM D 3244 : 2016 | Standard Practice for Utilization of Test Data to Determine Conformance with Specifications |
| ASTM D 4175 : 2009 : REV A : EDT 4 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2009 : REV A : EDT 3 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2699 : 2001 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 8047 : 2017 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
| ASTM D 4052 : 2009 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 5453 : 2008 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 5185 : 2002 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 2699 : 2003 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4485 : 2011 : REV B | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 4684 : 2007 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4485 : 2016 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 4175 : 2018 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4485 : 2007 | Standard Specification for Performance of Engine Oils |
| ASTM D 2700 : 2012 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4485 : 2010 | Standard Specification for Performance of Engine Oils |
| ASTM D 2699 : 2009 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5191 : 2001 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 5185 : 2018 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 2700 : 2012 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4485 : 2001 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 2700 : 1999 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1319 : 2002 : REV A | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 5453 : 2005 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 2700 : 2017 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4684 : 2017 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 8047 : 2018 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
| ASTM D 4175 : 2001 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2005 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2700 : 2016 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2700 : 2001 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5191 : 2010 : REV A | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 4739 : 2008 | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 2699 : 2012 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 3231 : 2018 | Standard Test Method for Phosphorus in Gasoline |
| ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 3237 : 2002 | Standard Test Method for Lead In Gasoline By Atomic Absorption Spectroscopy |
| ASTM D 5185 : 2013 : EDT 1 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 8047 : 2017 : REV A | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
| ASTM D 7320 : 2015 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 5452 : 2012 | Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration |
| ASTM D 2700 : 2006 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4485 : 2004 | Standard Specification for Performance of Engine Oils |
| ASTM D 2699 : 2016 : EDT 1 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5452 : 2000 | Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration |
| ASTM D 5453 : 2006 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 5293 : 2014 | Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –5°C and –35°C Using Cold-Cranking Simulator |
| ASTM D 7320 : 2016 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 4739 : 2017 | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 4684 : 2012 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 7320 : 2015 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 3231 : 2002 | Standard Test Method for Phosphorus in Gasoline |
| ASTM D 4739 : 2006 | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 2699 : 2011 : EDT 1 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4175 : 2015 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4485 : 2000 | Standard Specification for Performance of Engine Oils |
| ASTM D 4175 : 2002 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 3343 : 2005 : R2015 | Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels |
| ASTM D 3343 : 2016 | Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels |
| ASTM D 4739 : 1996 | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 4052 : 2011 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 5191 : 2012 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 2699 : 2012 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5293 : 2008 : EDT 1 | Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator |
| ASTM D 2699 : 2008 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2700 : 2013 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 1319 : 2003 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4052 : 2016 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 5452 : 2006 | Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration |
| ASTM D 4485 : 2015 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 3343 : 1990 | Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels |
| ASTM D 4815 : 1999 : EDT 1 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, <I>tertiary</I>-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
| ASTM D 2700 : 2018 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5185 : 2013 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 5191 : 2003 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 7320 : 2007 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 5293 : 2017 : REV A | Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator |
| ASTM D 4684 : 2014 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 5452 : 2005 | Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration |
| ASTM D 5453 : 2016 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 1319 : 2010 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4175 : 2009 : REV A : EDT 5 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2016 : REV C | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2700 : 2016 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4175 : 2015 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2699 : 2003 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2700 : 2003 : REV B | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5191 : 1999 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 7320 : 2011 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 7320 : 2006 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 7320 : 2017 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 2699 : 2018 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2700 : 2011 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4175 : 2015 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4485 : 2006 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 4739 : 2011 : R2017 | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 4815 : 2009 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
| ASTM D 4684 : 2002 : REV A | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 5453 : 2003 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 4175 : 2009 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4815 : 2015 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
| ASTM D 4815 : 2004 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
| ASTM D 4175 : 2016 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4815 : 1999 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, <I>tertiary</I>-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
| ASTM D 2700 : 2002 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2700 : 2007 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4175 : 2002 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2008 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5293 : 2009 | Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator |
| ASTM D 2699 : 2007 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4175 : 2002 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5191 : 2018 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 5453 : 2016 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 5191 : 2010 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 4175 : 2000 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2016 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 3237 : 2006 | Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy |
| ASTM D 2700 : 2004 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4815 : 2013 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
| ASTM D 4684 : 2007 : EDT 1 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4052 : 1996 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
| ASTM D 4739 : 2008 : EDT 1 | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 5191 : 2002 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 2699 : 2004 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2699 : 2015 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2699 : 2013 : REV B | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4684 : 1999 : EDT 1 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 2700 : 2013 : REV B | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 7320 : 2009 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 7320 : 2013 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 5191 : 2019 | Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method) |
| ASTM D 5293 : 1999 : REV A : EDT 1 | Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35<sup>o</sup>C Using the Cold-Cranking Simulator |
| ASTM D 4485 : 2005 | Standard Specification for Performance of Engine Oils |
| ASTM D 4684 : 2017 : REV A | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 5185 : 2009 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 2699 : 2001 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 7320 : 2008 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 2699 : 2006 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4815 : 2003 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
| ASTM D 5293 : 2017 : EDT 1 | Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator |
| ASTM D 4485 : 2014 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 5453 : 2019 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 2699 : 2015 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4485 : 2002 | Standard Specification for Performance of Engine Oils |
| ASTM D 4175 : 2017 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 7320 : 2018 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 4485 : 2005 : EDT 1 | Standard Specification for Performance of Engine Oils |
| ASTM D 2699 : 2002 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4175 : 2009 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2700 : 2017 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5185 : 2002 : EDT 1 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 7320 : 2017 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 3231 : 2007 | Standard Test Method for Phosphorus in Gasoline |
| ASTM D 2700 : 2003 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5191 : 2004 : REV A | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 3237 : 2017 | Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy |
| ASTM D 5453 : 2019 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 4175 : 2018 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2016 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 1319 : 2015 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 2699 : 2009 : EDT 1 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2699 : 2004 : EDT 1 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5293 : 2004 | Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator |
| ASTM D 2699 : 2006 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 3237 : 1997 | Standard Test Method for Lead In Gasoline By Atomic Absorption Spectroscopy |
| ASTM D 5185 : 2002 : EDT 2 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 5191 : 2007 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 5293 : 2015 | Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator |
| ASTM D 4684 : 2018 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4739 : 2011 | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 4739 : 2002 | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 1319 : 2013 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 5293 : 2008 | Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator |
| ASTM D 7320 : 2012 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 4052 : 2015 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 2700 : 2004 : EDT 1 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 3338 : 2005 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| ASTM D 3231 : 1989 | Standard Test Method for Phosphorus in Gasoline |
| ASTM D 2700 : 2001 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4739 : 2006 : REV A | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 5191 : 2015 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 8047 : 2016 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
| ASTM D 2699 : 2018 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4175 : 2017 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 7320 : 2010 : REV B | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 4815 : 2015 : REV A | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
| ASTM D 5293 : 2010 | Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator |
| ASTM D 7320 : 2016 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 7320 : 2010 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 4175 : 2019 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 3338 : 2008 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| ASTM D 3338 : 1995 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| ASTM D 2699 : 2013 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 3244 : 2007 : REV A | Standard Practice for Utilization of Test Data to Determine Conformance with Specifications |
| ASTM D 2700 : 2019 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4485 : 2009 | Standard Specification for Performance of Engine Oils |
| ASTM D 3343 : 1995 : R2000 | Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels |
| ASTM D 5452 : 2008 | Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration |
| ASTM D 4175 : 2015 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5191 : 2010 : REV B | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 4485 : 2010 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 5453 : 2003 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 5293 : 2017 | Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator |
| ASTM D 5293 : 2002 | Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator |
| ASTM D 4485 : 2011 | Standard Specification for Performance of Engine Oils |
| ASTM D 2699 : 2010 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5191 : 2013 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 3231 : 2011 | Standard Test Method for Phosphorus in Gasoline |
| ASTM D 3237 : 2012 | Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy |
| ASTM D 1319 : 2019 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 5191 : 2006 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
| ASTM D 4052 : 2018 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 2699 : 2019 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2700 : 2004 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 1319 : 2002 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4175 : 2008 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2700 : 2008 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 5453 : 2008 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 4485 : 2007 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 5453 : 2000 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.