ASTM D 8125 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Re-Refined Engine Oil Bottoms (REOB)/Vacuum Tower Asphalt Extender (VTAE)
Hardcopy , PDF
10-06-2024
English
06-07-2018
Committee |
D 04
|
DocumentType |
Standard
|
Pages |
2
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers re-refined engine oil bottoms, also known as vacuum tower asphalt extender, that may be used in formulating asphalt for pavement construction and roofing. This specification has been developed specifically for these two categories of product and is not intended for other uses. Table 1 is to be used for pavement construction and Table 2 for roofing. “Re-refined engine oil bottoms” (REOB) is the prevailing name used by many state highway agencies and FHWA, while “vacuum tower asphalt extender” (VTAE) is the preferred name used by the manufacturers of the product. Since each name provides an important descriptor of production elements (“re-refined” and “vacuum tower”) for the specific product this specification addresses, this specification uses the term “REOB/VTAE.”
1.2Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 8418 : 2021 | Standard Guide for Material and Construction Standards Related to Sustainability Within Committee D04 |
ASTM D 7553 : 2015 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
ASTM D 2042 : 2001 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene |
ASTM D 2872 : 2019 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
ASTM E 1131 : 2003 | Standard Test Method for Compositional Analysis by Thermogravimetry |
ASTM D 4402/D4402M : 2023 | Standard Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer |
ASTM D 7553 : 2015 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
ASTM E 1131 : 2008 : R2014 | Standard Test Method for Compositional Analysis by Thermogravimetry |
ASTM D 2042 : 1997 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene |
ASTM D 93 : 2019 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
ASTM D 93 : 1990 : EDT 1 | Standard Test Methods for Flash Point by Pensky-Martens Closed Tester |
ASTM E 1131 : 2020 | Standard Test Method for Compositional Analysis by Thermogravimetry |
ASTM D 2042 : 2009 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene |
ASTM D 2872 : 2012 : EDT 1 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
ASTM D 2042 : 2015 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene |
ASTM E 1131 : 2008 | Standard Test Method for Compositional Analysis by Thermogravimetry |
ASTM D 4402/D4402M : 2015 | Standard Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer |
ASTM D 7553 : 2009 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
ASTM D 7553 : 2010 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
ASTM D 2872 : 2012 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
ASTM D 2872 : 2021 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
ASTM D 8078 : 2018 : EDT 1 | Standard Test Method for Ash Content of Asphalt and Emulsified Asphalt Residues |
ASTM D 7553 : 2015 : R2021 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
ASTM D 93 : 2000 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
ASTM D 2872 : 2022 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test) |
ASTM D 93 : 1985 | Standard Test Method for Flash Point by Pensky-Martens Closed Tester |
ASTM E 1131 : 1998 | Standard Test Method for Compositional Analysis by Thermogravimetry |
ASTM D 2872 : 1997 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
ASTM D 2872 : 2004 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
ASTM D 2042 : 2022 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene or Toluene |
ASTM D 8078 : 2016 | Standard Test Method for Ash Content of Asphalt and Emulsified Asphalt Residues |
ASTM D 4402/D4402M : 2015 : R2022 | Standard Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer |
ASTM D 93 : 1997 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
ASTM D 93 : 2018 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
ASTM D 8078 : 2018 | Standard Test Method for Ash Content of Asphalt and Emulsified Asphalt Residues |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.