ASTM E 119 : 2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Fire Tests of Building Construction and Materials
Hardcopy , PDF
11-11-2014
English
31-12-2010
Committee |
E 05
|
DocumentType |
Test Method
|
Pages |
22
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 The test methods described in this fire-test-response standard are applicable to assemblies of masonry units and to composite assemblies of structural materials for buildings, including bearing and other walls and partitions, columns, girders, beams, slabs, and composite slab and beam assemblies for floors and roofs. They are also applicable to other assemblies and structural units that constitute permanent integral parts of a finished building.
1.2 It is the intent that classifications shall register comparative performance to specific fire-test conditions during the period of exposure and shall not be construed as having determined suitability for use under other conditions or after fire exposure.
1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.
1.4 These test methods prescribe a standard fire exposure for comparing the test results of building construction assemblies. The results of these tests are one factor in assessing predicted fire performance of building construction and assemblies. Application of these test results to predict the performance of actual building construction requires the evaluation of test conditions.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
ASTM C 11 : 2018 : REV B | Standard Terminology Relating to Gypsum and Related Building Materials and Systems |
ASTM C 1178/C1178M : 2018 | Standard Specification for Coated Glass Mat Water-Resistant Gypsum Backing Panel |
ASTM E 2536 : 2015 : REV A | Standard Guide for Assessment of Measurement Uncertainty in Fire Tests |
ASTM E 2874 : 2019 | Standard Test Method for Determining the Fire-Test Response Characteristics of a Building Spandrel-Panel Assembly Due to External Spread of Fire |
ASTM E 1966 : 2015 : R2019 | Standard Test Method for Fire-Resistive Joint Systems |
ASTM F 3059 : 2018 | Standard Specification for Fiber-Reinforced Polymer (FRP) Gratings Used in Marine Construction and Shipbuilding |
ASTM E 2336 : 2020 | Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems |
ASTM E 2226 : 2015 : REV B : R2019 | Standard Practice for Application of Hose Stream |
ASTM E 2750 : 2017 | Standard Guide for Extension of Data from Penetration Firestop System Tests Conducted in Accordance with ASTM E814 |
ASTM C 1825 : 2019 | Standard Guide for Developing Specifications for Masonry Units |
ASTM E 2061 : 2020 | Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles |
ASTM C 1396/C1396M : 2017 | Standard Specification for Gypsum Board |
ASTM E 2816 : 2020 : REV A | Standard Test Methods for Fire Resistive Metallic HVAC Duct Systems |
ASTM C 1423 : 2016 | Standard Guide for Selecting Jacketing Materials for Thermal Insulation |
ASTM E 2748 : 2012 : REV A : R2017 | Standard Guide for Fire-Resistance Experiments |
ASTM E 605/E605M : 2019 | Standard Test Methods for Thickness and Density of Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members |
ASTM E 2912 : 2017 | Standard Test Method for Fire Test of Non-Mechanical Fire Dampers Used in Vented Construction |
ASTM E 736/E736M : 2019 | Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members |
ASTM E 937/E937M : 1993 : R2020 | Standard Test Method for Corrosion of Steel by Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members |
ASTM C 887 : 2020 | Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar |
ASTM D 7374 : 2008 : R2015 | Standard Practice for Evaluating Elevated Temperature Performance of Adhesives Used in End-Jointed Lumber |
ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
ASTM E 2837 : 2013 : R2017 | Standard Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between Rated Wall Assemblies and Nonrated Horizontal Assemblies |
ASTM E 3134 : 2020 | Standard Specification for Transportation Tunnel Structural Components and Passive Fire Protection Systems |
ASTM E 1513/E1513M : 1993 : R2020 | Standard Practice for Application of Sprayed Fire-Resistive Materials (SFRMs) |
ASTM E 3057 : 2019 | Standard Test Method for Measuring Heat Flux Using Directional Flame Thermometers with Advanced Data Analysis Techniques |
ASTM E 2924 : 2014 : R2020 | Standard Practice for Intumescent Coatings |
ASTM E 759/E759M : 1992 : R2020 | Standard Test Method for Effect of Deflection on Sprayed Fire-Resistive Material Applied to Structural Members |
ASTM E 2032 : 2009 : R2017 | Standard Guide for Extension of Data From Fire Resistance Tests Conducted in Accordance with ASTM E 119 |
ASTM E 2634 : 2018 | Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems |
ASTM C 1278/C1278M : 2017 | Standard Specification for Fiber-Reinforced Gypsum Panel |
ASTM D 7470 : 2008 : R2015 | Standard Practice for Evaluating Elevated Temperature Performance of End-Jointed Lumber Studs |
ASTM E 1512 : 2001 : R2015 | Standard Test Methods for Testing Bond Performance of Bonded Anchors |
ASTM C 1852 : 2020 | Standard Guide for Product Selection/Delivery Systems for Aerosol Foam Sealants and Adhesives |
ASTM E 2307 : 2020 | Standard Test Method for Determining Fire Resistance of Perimeter Fire Barriers Using Intermediate-Scale, Multi-story Test Apparatus |
ASTM E 1529 : 2016 : EDT 1 | Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies |
ASTM C 926 : 2020 : REV B | Standard Specification for Application of Portland Cement-Based Plaster |
ASTM C 1766 : 2015(R2019) | Standard Specification for Factory-Laminated Gypsum Panel Products |
ASTM E 2785 : 2014 | Standard Test Method for Exposure of Firestop Materials to Severe Environmental Conditions |
ASTM D 7746 : 2011 : R2016 | Standard Practice for Calculating the Superimposed Load on Wood-frame Floor-Ceiling Assemblies for Standard Fire-Resistance Tests |
ASTM E 814 : 2013 : REV A : R2017 | Standard Test Method for Fire Tests of Penetration Firestop Systems |
ASTM E 1725 : 2019 | Standard Test Methods for Fire Tests of Fire-Resistive Barrier Systems for Electrical System Components |
ASTM E 3037 : 2020 | Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems |
ASTM E 3048 : 2019 : REV A | Standard Test Method for Determination of Time to Burn-Through Using the Intermediate Scale Calorimeter (ICAL) Radiant Panel |
ASTM E 2351 : 2004 : REV A : R2013 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Functionality (Withdrawn 2022) |
ASTM E 859/E859M : 1993 : R2020 | Standard Test Method for Air Erosion of Sprayed Fire-Resistive Materials (SFRMs) Applied to Structural Members |
ASTM D 6513 : 2014 | Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Resistance Tests |
ASTM C 1177/C1177M : 2017 | Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing |
ASTM E 760/E760M : 1992 : R2020 | Standard Test Method for Effect of Impact on Bonding of Sprayed Fire-Resistive Material Applied to Structural Members |
ASTM E 2568 : 2017 : REV A | Standard Specification for PB Exterior Insulation and Finish Systems |
ASTM E 2749 : 2015 : REV A : R2019 | Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens |
ASTM E 3157 : 2020 | Standard Guide for Understanding and Using Information Related to Installation of Firestop Systems |
ASTM C 1795 : 2017 | Standard Test Methods for High-Temperature Characterization of Gypsum Boards and Panels |
ASTM E 1494 : 2018 | Standard Practice for Testing Physical Properties of Friable Surfacing Materials |
ASTM E 761/E761M : 1992 : R2020 | Standard Test Method for Compressive Strength of Sprayed Fire-Resistive Material Applied to Structural Members |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.