• Shopping Cart
    There are no items in your cart

ASTM E 1225 : 2013 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique

Available format(s)

PDF

Superseded date

18-11-2020

Language(s)

English

Published date

01-10-2013

€67.30
Excluding VAT

CONTAINED IN VOL. 14.02, 2017 Defines a steady state technique for the determination of the thermal conductivity, lambda, of homogeneous-opaque solids.

Committee
E 37
DocumentType
Redline
Pages
13
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

1.1This test method describes a steady state technique for the determination of the thermal conductivity, λ, of homogeneous-opaque solids (see Notes 1 and 2). This test method is applicable to materials with effective thermal conductivities in the range 0.2 < λ < 200 W/(m·K) over the temperature range between 90 and 1300 K. It can be used outside these ranges with decreased accuracy.

Note 1For purposes of this technique, a system is homogeneous if the apparent thermal conductivity of the specimen, λ A, does not vary with changes of thickness or cross-sectional area by more than ±5 %. For composites or heterogeneous systems consisting of slabs or plates bonded together, the specimen should be more than 20 units wide and 20 units thick, respectively, where a unit is the thickness of the thickest slab or plate, so that diameter or length changes of one-half unit will affect the apparent λA by less than ±5 %. For systems that are non-opaque or partially transparent in the infrared, the combined error due to inhomogeneity and photon transmission should be less than ±5 %. Measurements on highly transparent solids must be accompanied with infrared absorption coefficient information, or the results must be reported as apparent thermal conductivity, λA.
Note 2This test method may also be used to evaluate the contact thermal conductance/resistance of materials.

1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SAE J 2581 : 2017 THERMAL TRANSPORT PROPERTIES GERMANE TO FRICTION MATERIALS AND BRAKES
14/30268442 DC : 0 BS 5930 - CODE OF PRACTICE FOR GROUND INVESTIGATIONS
ASTM D 1039 : 2016 : REDLINE Standard Test Methods for Glass-Bonded Mica Used as Electrical Insulation
ASTM D 6353 : 2006 : R2017 : EDT 1 Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production
SAE AIR 6232 : 2013 AIRCRAFT SURFACE COATING INTERACTION WITH AIRCRAFT DEICING/ANTI-ICING FLUIDS
ASTM C 1671 : 2015 : REDLINE Standard Practice for Qualification and Acceptance of Boron Based Metallic Neutron Absorbers for Nuclear Criticality Control for Dry Cask Storage Systems and Transportation Packaging
ASTM E 1652 : 2015 : REDLINE Standard Specification for Magnesium Oxide and Aluminum Oxide Powder and Crushable Insulators Used in the Manufacture of Base Metal Thermocouples, Metal-Sheathed Platinum Resistance Thermometers, and Noble Metal Thermocouples
MIL-I-49466 Base Document:1990 INSULATOR; DISKS, PLATES & WASHERS GENERAL SPECIFICATION FOR
ASTM D 5930 : 2017 : REDLINE Standard Test Method for Thermal Conductivity of Plastics by Means of a Transient Line-Source Technique
ASTM D 6353 : 2006 Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production
NACE RP 06 02 : 2002 FIELD-APPLIED COAL TAR ENAMEL PIPE COATING SYSTEMS: APPLICATION, PERFORMANCE, AND QUALITY CONTROL
NACE RP 03 99 : 2004 PLANT-APPLIED EXTERNAL COAL TAR ENAMEL PIPE COATING SYSTEMS: APPLICATION, PERFORMANCE, AND QUALITY CONTROL
ASTM E 1530 : 2011 Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
ASTM D 6353 : 2006 : R2011 Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production
ASTM C 1470 : 2006 : R2013 Standard Guide for Testing the Thermal Properties of Advanced Ceramics
ASTM D 5470 : 2017 : REDLINE Standard Test Method for Thermal Transmission Properties of Thermally Conductive Electrical Insulation Materials
ASTM C 1470 : 2006 Standard Guide for Testing the Thermal Properties of Advanced Ceramics
ASTM E 1530 : 2011 : R2016 Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
BS 5930:2015 Code of practice for ground investigations

ASTM E 230 : 2003 Standard Specification and Temperature-Electromotive Force (EMF) Tables for Standardized Thermocouples

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.