• Shopping Cart
    There are no items in your cart

ASTM E 1245 : 2003

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Practice for Determining the Inclusion or Second-Phase Constituent Content of Metals by Automatic Image Analysis

Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

10-01-2003

€67.30
Excluding VAT

CONTAINED IN VOL. 03.01, 2016 Defines a procedure for obtaining stereological measurements that describe basic characteristics of the morphology of indigenous inclusions in steels and other metals using automatic image analysis.

Committee
E 04
DocumentType
Standard Practice
Pages
8
ProductNote
Reconfirmed 2003
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1 This practice describes a procedure for obtaining stereological measurements that describe basic characteristics of the morphology of indigenous inclusions in steels and other metals using automatic image analysis. The practice can be applied to provide such data for any discrete second phase.

Note 1—Stereological measurement methods are used in this practice to assess the average characteristics of inclusions or other second-phase particles on a longitudinal plane-of-polish. This information, by itself, does not produce a three-dimensional description of these constituents in space as deformation processes cause rotation and alignment of these constituents in a preferred manner. Development of such information requires measurements on three orthogonal planes and is beyond the scope of this practice.

1.2 This practice specifically addresses the problem of producing stereological data when the features of the constituents to be measured make attainment of statistically reliable data difficult.

1.3 This practice deals only with the recommended test methods and nothing in it should be construed as defining or establishing limits of acceptability.

1.4 The measured values are stated in SI units, which are to be regarded as standard. Equivalent inch-pound values are in parentheses and may be approximate.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F 3160 : 2016 Standard Guide for Metallurgical Characterization of Absorbable Metallic Materials for Medical Implants
ASTM E 1382 : 1997 : R2015 Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis
ASTM E 2283 : 2008 : R2014 Standard Practice for Extreme Value Analysis of Nonmetallic Inclusions in Steel and Other Microstructural Features
ASTM E 2142 : 2008 : R2015 Standard Test Methods for Rating and Classifying Inclusions in Steel Using the Scanning Electron Microscope
ASTM F 2063 : 2018 Standard Specification for Wrought Nickel-Titanium Shape Memory Alloys for Medical Devices and Surgical Implants
ASTM F 1376 : 1992 : R2012 Standard Guide for Metallurgical Analysis for Gas Distribution System Components
ASTM E 606/E606M : 2012 Standard Test Method for Strain-Controlled Fatigue Testing
ASTM E 45 : 2018 : REV A Standard Test Methods for Determining the Inclusion Content of Steel
ASTM E 562 : 2011 Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count
ASTM A 892 : 2009 : R2014 : EDT 1 Standard Guide for Defining and Rating the Microstructure of High Carbon Bearing Steels
ASTM E 2109 : 2001 : R2014 Standard Test Methods for Determining Area Percentage Porosity in Thermal Sprayed Coatings
ASTM E 3 : 2011 : R2017 Standard Guide for Preparation of Metallographic Specimens
ASTM E 768 : 1999 : R2018 Standard Guide for Preparing and Evaluating Specimens for Automatic Inclusion Assessment of Steel
ISO 17781:2017 Petroleum, petrochemical and natural gas industries — Test methods for quality control of microstructure of ferritic/austenitic (duplex) stainless steels

ASTM E 7 : 2017 : REDLINE Standard Terminology Relating to Metallography
ASTM E 768 : 1999 : R2018 Standard Guide for Preparing and Evaluating Specimens for Automatic Inclusion Assessment of Steel

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.