ASTM E 21 : 2020
Current
Current
The latest, up-to-date edition.
Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-10-2020
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
E 28
|
| DocumentType |
Test Method
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1These test methods cover procedure and equipment for the determination of tensile strength, yield strength, elongation, and reduction of area of metallic materials at elevated temperatures.
1.2Determination of modulus of elasticity and proportional limit are not included.
1.3Tension tests under conditions of rapid heating or rapid strain rates are not included.
1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 3184 : 2016 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
| ASTM E 139 : 2011 : R2018 | Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials |
| ASTM C 1671 : 2020 : REV A | Standard Practice for Qualification and Acceptance of Boron Based Metallic Neutron Absorbers for Nuclear Criticality Control for Dry Cask Storage Systems and Transportation Packaging |
| ASTM A 1077/A1077M : 2014 | Standard Specification for Structural Steel with Improved Yield Strength at High Temperature for Use in Buildings |
| ASTM F 3302 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Titanium Alloys via Powder Bed Fusion |
| ASTM E 111 : 2017 | Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus |
| ASTM A 193/A193M : 2020 | Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications |
| ASTM A 1095 : 2015 : R2019 | Standard Specification for High-Silicon Molybdenum Ferritic Iron Castings |
| ASTM F 3122 : 2014 | Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes |
| ASTM E 2215 : 2019 | Standard Practice for Evaluation of Surveillance Capsules from Light-Water Moderated Nuclear Power Reactor Vessels |
| ASTM B 351/B351M : 2013 : R2018 | Standard Specification for Hot-Rolled and Cold-Finished Zirconium and Zirconium Alloy Bars, Rod, and Wire for Nuclear Application |
| ASTM B 352/B352M : 2017 | Standard Specification for Zirconium and Zirconium Alloy Sheet, Strip, and Plate for Nuclear Application |
| ASTM F 3055 : 2014 : REV A | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion |
| ASTM E 1012 : 2019 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM C 1366 : 2019 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Elevated Temperatures |
| ASTM F 2281 : 2004 : R2017 | Standard Specification for Stainless Steel and Nickel Alloy Bolts, Hex Cap Screws, and Studs, for Heat Resistance and High Temperature Applications |
| ASTM A 732/A732M : 2020 | Standard Specification for Castings, Investment, Carbon and Low-Alloy Steel for General Application, and Cobalt Alloy for High Strength at Elevated Temperatures |
| ASTM B 655/B655M : 2010 : R2018 | Standard Specification for Niobium-Hafnium Alloy Bar and Wire |
| ASTM B 776 : 2012 : R2019 | Standard Specification for Hafnium and Hafnium Alloy Strip, Sheet, and Plate |
| ASTM E 209 : 2018 | Standard Practice for Compression Tests of Metallic Materials at Elevated Temperatures with Conventional or Rapid Heating Rates and Strain Rates |
| ASTM E 531 : 2013 | Standard Practice for Surveillance Testing of High-Temperature Nuclear Component Materials (Withdrawn 2022) |
| ASTM A 579/A579M : 2020 | Standard Specification for Superstrength Alloy Steel Forgings (Withdrawn 2024) |
| ASTM E 1820 : 2020 : REV B | Standard Test Method for Measurement of Fracture Toughness |
| ASTM E 185 : 2016 | Standard Practice for Design of Surveillance Programs for Light-Water Moderated Nuclear Power Reactor Vessels |
| ASTM E 83 : 2016 | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM B 737 : 2010 : R2021 | Standard Specification for Hot-Rolled and/or Cold-Finished Hafnium Rod and Wire |
| ASTM F 3056 : 2014 : EDT 1 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N06625) with Powder Bed Fusion |
| ASTM E 3097 : 2017 | Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys |
| ASTM B 353 : 2012 : R2017 | Standard Specification for Wrought Zirconium and Zirconium Alloy Seamless and Welded Tubes for Nuclear Service (Except Nuclear Fuel Cladding) |
| ASTM E 3098 : 2017 | Standard Test Method for Mechanical Uniaxial Pre-strain and Thermal Free Recovery of Shape Memory Alloys |
| ASTM E 2448 : 2018 | Standard Test Method for Determining the Superplastic Properties of Metallic Sheet Materials |
| ASTM B 811 : 2013 : R2017 | Standard Specification for Wrought Zirconium Alloy Seamless Tubes for Nuclear Reactor Fuel Cladding |
| ASTM E 633 : 2021 | Standard Guide for Use of Thermocouples in Elevated-Temperature Mechanical Testing |
| ASTM A 20/A20M : 2020 | Standard Specification for General Requirements for Steel Plates for Pressure Vessels |
| ASTM F 2924 : 2014 | Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion |
| ASTM F 3213 : 2017 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Cobalt-28 Chromium-6 Molybdenum via Powder Bed Fusion |
| ASTM A 608/A608M : 2020 | Standard Specification for Centrifugally Cast Iron-Chromium-Nickel High-Alloy Tubing for Pressure Application at High Temperatures |
| ASTM B 661 : 2012 : R2020 | Standard Practice for Heat Treatment of Magnesium Alloys |
| ASTM F 3318 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam |
| ASTM E 3205 : 2020 | Standard Test Method for Small Punch Testing of Metallic Materials |
| ASTM B 654/B654M : 2010 : R2018 | Standard Specification for Niobium-Hafnium Alloy Foil, Sheet, Strip, and Plate |
| ASTM C 1359 : 2018 : EDT 1 | Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics With Solid Rectangular Cross Section Test Specimens at Elevated Temperatures |
| ASTM A 447/A447M : 2011 : R2021 | Standard Specification for Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service |
| ASTM A 1099/A1099M : 2020 | Standard Specification for Modified Alloy Steel Forgings, Forged Bar, and Rolled Bar Commonly Used in Oil and Gas Pressure Vessels |
| ASTM E 8/E8M : 2024 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 220 : 2019 | Standard Test Method for Calibration of Thermocouples By Comparison Techniques |
| ASTM E 83 : 2023 | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM E 8/E8M : 2016 : REV A : EDT 1 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 83 : 2000 : EDT 1 | Standard Practice for Verification and Classification of Extensometer |
| ASTM E 8/E8M : 2021 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 83 : 1998 : EDT 1 | Standard Practice for Verification and Classification of Extensometer |
| ASTM E 633 : 2021 : REV A | Standard Guide for Use of Thermocouples in Elevated-Temperature Mechanical Testing |
| ASTM E 6 : 2002 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 6 : 2015 : EDT 3 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 6 : 2023 : REV A | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 633 : 2021 | Standard Guide for Use of Thermocouples in Elevated-Temperature Mechanical Testing |
| ASTM E 6 : 2015 : EDT 4 : REDLINE | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 633 : 2013 | Standard Guide for Use of Thermocouples in Creep and Stress-Rupture Testing to 1800°F (1000°C) in Air |
| ASTM E 6 : 2015 : EDT 4 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 6 : 2023 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 4 : 2024 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.