ASTM E 2179 : 2003 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors
Hardcopy , PDF
11-11-2014
English
31-12-2010
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 04.06, 2016 Defines a method for the laboratory measurement of the effectiveness of floor coverings in reducing impact noise from a standard tapping machine through concrete floors.
| Committee |
E 33
|
| DocumentType |
Test Method
|
| Pages |
5
|
| ProductNote |
Reconfirmed EDT 1
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method describes a method for the laboratory measurement of the effectiveness of floor coverings in reducing impact noise from a standard tapping machine through concrete floors. The test results are not necessarily directly related to the subjective evaluations of the floor coverings.
1.2 This test method applies to all floor coverings, whether single or multi-layered, as installed on a standard concrete floor. Multi-layered coverings may be factory-assembled or assembled at the test laboratory.
1.3 The test method applies only to laboratory measurements. It does not apply to the measurement of the effectiveness of a floor covering in a field situation.
1.4 Laboratory Accreditation—A procedure for accrediting a laboratory for performing this test method is given in Method E 492.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM E 2813 : 2018 | Standard Practice for Building Enclosure Commissioning |
| ASTM E 989 : 2018 | Standard Classification for Determination of Single-Number Metrics for Impact Noise |
| ASTM E 3133 : 2018 | Standard Test Method for Laboratory Measurement of Floor Impact Sound Radiation Using the Tapping Machine |
| ASTM C 634 : 2013 : EDT 1 | Standard Terminology Relating to Building and Environmental Acoustics |
| ASTM C 634 : 2013 : R2021 | Standard Terminology Relating to Building and Environmental Acoustics |
| ASTM E 3133 : 2018 : EDT 1 | Standard Test Method for Laboratory Measurement of Floor Impact Sound Radiation Using the Tapping Machine (Withdrawn 2023) |
| ASTM E 3222 : 2020 : REV A | Standard Classification for Determination of High-frequency Impact Sound Ratings |
| ISO 717-2:2013 | Acoustics Rating of sound insulation in buildings and of building elements Part 2: Impact sound insulation |
| ISO 140-6:1998 | Acoustics Measurement of sound insulation in buildings and of building elements Part 6: Laboratory measurements of impact sound insulation of floors |
| ANSI S1.11 : 2014 | SPECIFICATION FOR OCTAVE-BAND AND FRACTIONAL-OCTAVE-BAND ANALOG AND DIGITAL FILTERS |
| ANSI/ASA S1.6 : 2016 | PREFERRED FREQUENCIES AND FILTER BAND CENTER FREQUENCIES FOR ACOUSTICAL MEASUREMENTS |
| ANSI S1.10 : 66(R2001) | AMERICAN NATIONAL STANDARD METHOD FOR THE CALIBRATION OF MICROPHONES |
| ISO 140-8:1997 | Acoustics Measurement of sound insulation in buildings and of building elements Part 8: Laboratory measurements of the reduction of transmitted impact noise by floor coverings on a heavyweight standard floor |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.