ASTM E 2886/E2886M : 2014
Current
The latest, up-to-date edition.
Standard Test Method for Evaluating the Ability of Exterior Vents to Resist the Entry of Embers and Direct Flame Impingement
Hardcopy , PDF
English
01-05-2014
This fire-test-response standard prescribes two individual methods to evaluate the ability of a gable end, crawl space (foundation) and other vents that mount on a vertical wall or in the under-eave area to resist the entry through the vent opening of embers and flame.
Committee |
E 05
|
DocumentType |
Test Method
|
Pages |
14
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
1.1This fire-test-response standard prescribes two individual methods to evaluate the ability of a gable end, crawl space (foundation) and other vents that mount on a vertical wall or in the under-eave area to resist the entry through the vent opening of embers and flame. The ability of such vents to completely exclude entry of flames or embers is not evaluated. Roof ridge and off-ridge (field) vents are excluded from this standard. Acceptance criteria are not provided in this standard.
1.2Ember entry and flame penetration are evaluated separately using different test procedures. A commentary and summary of the development of the ember test apparatus are given in Appendix X1.
1.3These laboratory tests are used to evaluate the response of vents when subjected to ember and flame exposures under controlled conditions.
1.4Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in non-conformance with the standard.
1.5Unless otherwise specified, the tolerance for dimensions in figures and text in this document shall be ±5 %.
1.6This test method does not address interior fire spread.
1.7The standard is used to measure and describe the response of materials, products or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessments of the materials, products or assemblies and other cladding materials under actual fire conditions.
1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.9Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
NFPA 1144 : 2018 | REDUCING STRUCTURE IGNITION HAZARDS FROM WILDLAND FIRE |
ASTM E 2957 : 2017 : REDLINE | Standard Test Method for Resistance to Wildfire Penetration of Eaves, Soffits and Other Projections |
ASTM E 2707 : 2015 | Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure |
ASTM E 2912 : 2013 | Standard Test Method for Fire Test of Non-Mechanical Fire Dampers Used in Vented Construction |
ASTM D 1929 : 2012 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM D 1929 : 2016 : REDLINE | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM D 1929 : 2019 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM E 2257 : 2013 : REV A | Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies |
ASTM D 1929 : 1996 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM E 2707 : 2014 | Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure |
ASTM D 1929 : 2013 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM D 1929 : 2014 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM E 108 : 2017 : REDLINE | Standard Test Methods for Fire Tests of Roof Coverings |
ASTM E 2257 : 2016 | Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies |
ASTM D 1929 : 2016 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM D 1929 : 2013 : REV A | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM D 1929 : 2020 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM E 2257 : 2013 | Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies |
ASTM E 2257 : 2017 : REDLINE | Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies |
ASTM E 2257 : 2008 | Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies |
ASTM E 2257 : 2017 | Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies |
ASTM E 2912 : 2017 : REDLINE | Standard Test Method for Fire Test of Non-Mechanical Fire Dampers Used in Vented Construction |
ASTM E 2257 : 2003 | Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies |
ASTM D 1929 : 2011 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM D 1929 : 2010 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM E 2912 : 2017 | Standard Test Method for Fire Test of Non-Mechanical Fire Dampers Used in Vented Construction |
ASTM E 2707 : 2015 : REDLINE | Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure |
ASTM E 2707 : 2009 | Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.