ASTM E 3246 : 2021
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Differential Indentation Depth Hardness of Metallic Materials
Hardcopy , PDF
06-06-2023
English
09-03-2021
Committee |
E 28
|
DocumentType |
Test Method
|
Pages |
18
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This test method covers the determination of the Differential Indentation Depth hardness of metallic materials by the Differential Indentation Depth hardness principle. This standard provides the requirements for Differential Indentation Depth hardness testing machines and the procedures for performing Differential Indentation Depth hardness tests.
1.2This standard includes additional requirements in annexes:
Verification of Differential Indentation Depth Hardness Testing Machines | Annex A1 |
Guidelines for Determining the Minimum Thickness of a Test Piece | Annex A2 |
1.3This standard includes non-mandatory information in appendixes which relates to the Differential Indentation Depth hardness test.
List of ASTM Standards Giving Hardness Numbers Corresponding to Tensile Strength | Appendix X1 |
Examples of Procedures for Determining Differential Indentation Depth Hardness Uncertainty | Appendix X2 |
Examples of Indenters Used in Differential Indentation Depth Machines | Appendix X3 |
1.4Units—This standard specifies the units of force and length in the International System of Units (SI); that is, force in Newtons (N) and length in micrometers (µm). However, because of continued common usage, values are provided in other units of measure for information.
1.5The test principles, testing procedures, and verification procedures are essentially identical for all the Differential Indentation Depth hardness testing instruments. The testing instruments may use different test forces and indenter shapes. The type and size of the indenters are matched to the design of the instrument by the manufacturer. Accordingly, the indenters, probes and other instrument components are generally not interchangeable among manufacturers.
1.6The hardness number reported by these instruments are based on direct correlations to existing hardness scales as determined by each manufacturer for each instrument and hardness scale. Unless otherwise noted on the instrument or in the operating manual for the instrument, the hardness numbers reported by the instrument are only applicable to non-austenitic steels. See 5.6.1 for additional information.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM A 370 : 2021 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
ASTM B 370 : 2012 : R2019 | Standard Specification for Copper Sheet and Strip for Building Construction |
ASTM B 134/B134M : 2015 : R2021 | Standard Specification for Brass Wire |
ASTM B 134/B134M : 2015 | Standard Specification for Brass Wire |
ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM A 370 : 2020 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM E 6 : 2015 : EDT 3 | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 6 : 2015 : EDT 4 : REDLINE | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM E 384 : 2017 | Standard Test Method for Microindentation Hardness of Materials |
ASTM B 370 : 2022 | Standard Specification for Copper Sheet and Strip for Building Construction |
ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.