• Shopping Cart
    There are no items in your cart

ASTM E 606/E606M : 2021

Current

Current

The latest, up-to-date edition.

Standard Test Method for Strain-Controlled Fatigue Testing

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

02-07-2021

€61.92
Excluding VAT

Committee
E 08
DocumentType
Test Method
Pages
16
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1This test method covers the determination of fatigue properties of nominally homogeneous materials by the use of test specimens subjected to uniaxial forces. It is intended as a guide for fatigue testing performed in support of such activities as materials research and development, mechanical design, process and quality control, product performance, and failure analysis. While this test method is intended primarily for strain-controlled fatigue testing, some sections may provide useful information for force-controlled or stress-controlled testing.

1.2The use of this test method is limited to specimens and does not cover testing of full-scale components, structures, or consumer products.

1.3This test method is applicable to temperatures and strain rates for which the magnitudes of time-dependent inelastic strains are on the same order or less than the magnitudes of time-independent inelastic strains. No restrictions are placed on environmental factors such as temperature, pressure, humidity, medium, and others, provided they are controlled throughout the test, do not cause loss of or change in dimension with time, and are detailed in the data report.

Note 1:The term inelastic is used herein to refer to all nonelastic strains. The term plastic is used herein to refer only to the time-independent (that is, noncreep) component of inelastic strain. To truly determine a time-independent strain the force would have to be applied instantaneously, which is not possible. A useful engineering estimate of time-independent strain can be obtained when the strain rate exceeds some value. For example, a strain rate of 1 × 10−3 sec−1 is often used for this purpose. This value should increase with increasing test temperature.

1.4This test method is restricted to the testing of uniform gage section test specimens subjected to axial forces as shown in Fig. 1(a). Testing is limited to strain-controlled cycling. The test method may be applied to hourglass specimens, see Fig. 1(b), but the user is cautioned about uncertainties in data analysis and interpretation. Testing is done primarily under constant amplitude cycling and may contain interspersed hold times at repeated intervals. The test method may be adapted to guide testing for more general cases where strain or temperature may vary according to application specific histories. Data analysis may not follow this test method in such cases.

FIG. 1Recommended Low-Cycle Fatigue Specimens

Recommended Low-Cycle Fatigue SpecimensRecommended Low-Cycle Fatigue Specimens

Note 1:* Dimension d is recommended to be 6.35 mm [0.25 in.]. See 7.1. Centers permissible. ** This diameter may be made greater or less than 2d depending on material hardness. In typically ductile materials diameters less than 2d are often employed and in typically brittle materials diameters greater than 2d may be found desirable.

Note 2:Threaded connections are more prone to inferior axial alignment and have greater potential for backlash, particularly if the connection with the grip is not properly designed.

1.5The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM A 988/A988M : 2017 Standard Specification for Hot Isostatically-Pressed Stainless Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
ASTM B 595 : 2021 Standard Specification for Materials for Aluminum Powder Metallurgy (PM) Structural Parts
ASTM E 2207 : 2015 : R2021 Standard Practice for Strain-Controlled Axial-Torsional Fatigue Testing with Thin-Walled Tubular Specimens
ASTM A 989/A989M : 2018 Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
ASTM E 739 : 2010 : R2015 Standard Practice for Statistical Analysis of Linear or Linearized Stress-Life (<emph type="bdit">S-N</emph>) and Strain-Life (ε-<emph type="bdit" >N</emph>) Fatigue Data

ASTM E 1049 : 1985 : R2017 Standard Practices for Cycle Counting in Fatigue Analysis
ASTM A 370 : 2021 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM E 1823 : 2024 Standard Terminology Relating to Fatigue and Fracture Testing
ASTM E 8/E8M : 2024 Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 83 : 2023 Standard Practice for Verification and Classification of Extensometer Systems
ASTM E 1823 : 2024 : REV A Standard Terminology Relating to Fatigue and Fracture Testing
ASTM A 370 : 2024 : REV A Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM E 8/E8M : 2021 Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 83 : 2016 Standard Practice for Verification and Classification of Extensometer Systems
ASTM E 1049 : 1985 : R2023 Standard Practices for Cycle Counting in Fatigue Analysis
ASTM E 384 : 2022 Standard Test Method for Microindentation Hardness of Materials
ASTM E 399 : 2024 Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials
ASTM E 83 : 1998 : EDT 1 Standard Practice for Verification and Classification of Extensometer
ASTM E 337 : 2015 : R2023 Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
ASTM E 337 : 2015 Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
ASTM E 3 : 2011 : R2017 Standard Guide for Preparation of Metallographic Specimens
ASTM E 384 : 2011 Standard Test Method for Knoop and Vickers Hardness of Materials
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 1823 : 2024 : REV B Standard Terminology Relating to Fatigue and Fracture Testing
ASTM E 399 : 2020 : REV A Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials
ASTM E 691 : 2023 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 739 : 2023 Standard Guide for Statistical Analysis of Linear or Linearized Stress-Life (<emph type="bdit">S-N</emph>) and Strain-Life (ε-<emph type="bdit" >N</emph>) Fatigue Data (Withdrawn 2024)
ASTM E 399 : 2023 Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials
ASTM E 1823 : 2021 Standard Terminology Relating to Fatigue and Fracture Testing
ASTM A 370 : 2020 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM E 8/E8M : 2022 Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM A 370 : 2023 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM E 466 : 2021 Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials
ASTM E 4 : 2021 Standard Practices for Force Calibration and Verification of Testing Machines
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 9 : 1989 : REV A : R1995 Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature
ASTM E 468 : 2018 Standard Practice for Presentation of Constant Amplitude Fatigue Test Results for Metallic Materials
ASTM A 370 : 2022 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM E 384 : 2017 Standard Test Method for Microindentation Hardness of Materials
ASTM E 112 : 2013 : R2021 Standard Test Methods for Determining Average Grain Size
ASTM E 112 : 2013 Standard Test Methods for Determining Average Grain Size
ASTM E 1245 : 2003 : R2016 Standard Practice for Determining the Inclusion or Second-Phase Constituent Content of Metals by Automatic Image Analysis
ASTM E 1823 : 2024 : REV C Standard Terminology Relating to Fatigue and Fracture Testing
ASTM E 1823 : 2023 Standard Terminology Relating to Fatigue and Fracture Testing
ASTM E 399 : 2022 Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials
ASTM E 1823 : 2020 : REV B Standard Terminology Relating to Fatigue and Fracture Testing
ASTM E 112 : 2024 Standard Test Methods for Determining Average Grain Size
ASTM E 1245 : 2003 : R2023 Standard Practice for Determining the Inclusion or Second-Phase Constituent Content of Metals by Automatic Image Analysis
ASTM A 370 : 2024 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM E 4 : 2024 Standard Practices for Force Calibration and Verification of Testing Machines

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.