ASTM F 1387 : 1999 : R2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
English
01-05-2012
23-09-2023
CONTAINED IN VOL. 01.07, 2018 Describes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems.
| Committee |
F 25
|
| DevelopmentNote |
Supersedes MIL C 24706. (04/2013)
|
| DocumentType |
Standard
|
| Pages |
29
|
| ProductNote |
Reconfirmed 2012
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This specification establishes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. The seal may be created via the mechanical deformation or created independently. Successful completion of the tests described constitutes completion of the technical portion of the qualification process.
1.2 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified in part or whole by the purchaser in the order. Unless otherwise specified, U.S. Navy contracts shall invoke the supplementary requirements in whole.
1.3 Unless specific MAF types are specified, the term “MAF” shall apply to all types described herein.
1.4 The tests specified in Section 13 and described in Annex A1 and Supplementary Requirements are applicable only to ascertain the performance characteristics of MAFs. These tests are not intended for use in the evaluation of non-MAF products.
1.5 A fire performance test is specified in Supplementary Requirement S7. This test provides general guidelines to determine the responsiveness of MAFs when subjected to fire. This test should not be considered for use to evaluate non-MAF products.
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.7 The following safety hazards caveat applies only to the tests listed in Section 13 and the tests described in the Supplementary Section and the Annex of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM F 2363/F2363M : 2017 | Standard Specification for Sewage and Graywater Flow Through Treatment Systems |
| MIL-STD-271 Revision F:1986 | REQUIREMENTS FOR NONDESTRUCTIVE TESTING METHODS (REPLACEMENT DOCUMENT NAVSEA TECH PUB T9074-AS-GIB-010/271) |
| AND10102 Revision 3:1965 | TUBING - STANDARD DIMENSIONS FOR ROUND SEAMLESS ALLOY STEEL (NO S/S DOCUMENT) |
| MIL L 7808 : K (1) | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
| ASTM A 262 : 2015 : REDLINE | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| MIL-T-8606 Revision C:1973 | Tubing, Steel, Corrosion-Resistant (18-8 Stabilized and Extra Low Carbon) (Use SAE-AMS5560, SAE-AMS5563, SAE-AMS5564, SAE-AMS5565, SAE-AMS5566, SAE-AMS5567, SAE-AMS5569, SAE-AMS5570, SAE-AMS5571, SAE-AMS5639 and SAE-AMS5668) |
| ASTM B 154 : 2016 : REDLINE | Standard Test Method for Mercurous Nitrate Test for Copper Alloys |
| QQ-N-286 Revision G:2000 | NICKEL-COPPER-ALUMINUM ALLOY, WROUGHT (UNS N05500) |
| MIL-P-24691-3 Base Document:1987 | Pipe And Tube, Corrosion-Resistant, Stainless Steel, Seamless Or Welded |
| QQ-P-35 Revision C:1988 | Passivation Treatments for Corrosion-Resistant Steel (S/Sby ASTM-A967or SAE-AMS-QQ-P-35) |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| MIL-P-24691-2 Base Document:1987 | Pipe And Tube, Chromium-Molybdenum Steel, Seamless |
| ASTM E 1529 : 2000 | Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies |
| ASTM E 1529 : 2016 : EDT 1 | Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies |
| SAE AMS5643U | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb (Nb) - 4.0Cu Solution Heat Treated, Precipitation Hardenable |
| ASTM E 1529 : 2010 | Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies |
| MIL-STD-1235 Revision C:1988 | SINGLE AND MULTILEVEL CONTINUOUS SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES (NO S/S DOCUMENT) |
| QQ-B-626 Revision D:1973 | Brass, Leaded and Nonleaded: Rod, Shapes, Forgings, and Flat Products with Finished Edges (Bar and Strip) (S/S by ASTM-B121, ASTM-B36, ASTM-B16, ASTM-B16M, AND ASTM-B124) |
| MIL-STD-45662 Revision A:1988 | Calibration Systems Requirements (Refer to ISO-10012-1 and ANSI-Z540-1 or Comparable Standards as Alternatives to MIL-STD-45662) |
| ASTM E 1529 : 2014 : REV A | Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies |
| MIL-P-24691-1 Base Document:1987 | Pipe And Tube, Carbon Steel, Seamless |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| ASTM B 124 : 2008 | SPECIFICATION FOR COPPER AND COPPER ALLOY FORGING ROD, BAR AND SHAPES |
| MIL-STD-2175 Revision A:1993 | CASTINGS, CLASSIFICATION AND INSPECTION OF (S/S BY SAE-AMS-STD-2175) |
| ASTM A 380 : 2006 | Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems |
| ASTM E 1529 : 2013 | Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies |
| MIL R 83248/1 : A | RUBBER, FLUOROCARBON ELASTOMER, HIGH TEMPERATURE, FLUID AND COMPRESSION SET RESISTANT (O-RINGS, CLASS 1, 75 HARDNESS) |
| MIL-STD-889 Revision C:2016 | Galvanic Compatibility of Electrically Conductive Materials |
| ASTM A 766/A766M : 1987 | Specification for Forgings |
| MIL-C-20159 Revision C:1985 | Copper-Nickel Alloy Castings (UNS No. C96200 and C96400) (S/S by ASTM-B369) |
| ASTM E 1529 : 2006 | Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies |
| ASTM E 1529 : 2016 | Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies |
| MS33531 Revision A:1957 | TOLERANCE, WELDED CORROSION-RESISTANT STEEL TUBING (ASG) (S/S BY SAE-AMS2243) |
| MIL H 83282 : C | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, AIRCRAFT, METRIC, NATO CODE NUMBER H 537 |
| SAE J515_201511 | Specification for O-Ring Materials Used with Hydraulic Connectors |
| MIL-STD-777 Revision F:2012 | Schedule of Piping, Valves, Fittings, and Associated Piping Components for Naval Surface Ships |
| ASME B36.10M : 2015 | WELDED AND SEAMLESS WROUGHT STEEL PIPE |
| MIL-STD-278 Revision F:1987 | WELDING AND CASTING STANDARD (REPLACEMENT DOCUMENT NAVSEA TECH PUB S9074-AR-GIB-010/278) |
| SAE J514_201201 | Hydraulic Tube Fittings |
| MIL-STD-753 Revision C:1990 | CORROSION-RESISTANT STEEL PARTS: SAMPLING, INSPECTION AND TESTING FOR SURFACE PASSIVATION (S/S BY SAE-AMS-STD-753) |
| QQ-S-763 Revision F:1996 | STEEL BARS, WIRE, SHAPES, AND FORGINGS; CORROSION RESISTANT (S/S BY SAE-AMS-QQ-S-763) |
| MIL S 901 : D | SHOCK TESTS, HI [HIGH IMPACT] SHIPBOARD MACHINERY, EQUIPMENT AND SYSTEMS, REQUIREMENTS FOR |
| ASTM A 105/A105M : 2014-11 | SPECIFICATION FOR CARBON STEEL FORGINGS FOR PIPING APPLICATIONS |
| ASTM E 1529 : 2014 | Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies |
| ASTM A 530/A530M : 2012-06 | SPECIFICATION FOR GENERAL REQUIREMENTS FOR SPECIALIZED CARBON AND ALLOY STEEL PIPE |
| MIL-STD-167 Base Document:1993 | MECHANICAL VIBRATIONS OF SHIPBOARD EQUIPMENT (REPLACED BY MIL-STD-167-1 AND MIL-STD-167-2) |
| MIL H 5606 : G | HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT; MISSILE AND ORDNANCE |
| QQ-P-416 Revision F:1991 | Plating, Cadmium (Electrodeposited) (S/Sby SAE-AMS-QQ-P-416) |
| MIL-T-24107 Revision B:1987 | Tube, Copper (Seamless) (Copper Alloy Numbers C10100, C10200, C10300, C10800, C12000, C12200, and C14200) |
| ASTM A 312/A312M : 2017-03 | SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES |
| DOD P 16232 : F | PHOSPHATE COATING, HEAVY, MANGANESE OR ZINC BASE (FOR FERROUS METALS) |
| MIL-STD-105 Revision E:1989 | Sampling Procedures and Tables for Inspection by Attributes (See Notice 3 for Replacement Information) |
| MIL-C-15726 Revision F:1988 | Copper-Nickel Alloy, Sheet, Plate, Strip, Bar, Rod and Wire |
| ASTM B 122/B122M : 2016 : REDLINE | Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.