ASTM F 1499 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
10-09-2022
English
12-12-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.04, 2017 Defines coextruded composite drain, waste, and vent pipe (DWV).
| Committee |
F 17
|
| DocumentType |
Redline
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers coextruded composite drain, waste, and vent pipe (DWV). The pipe is produced in Schedule 40 IPS sizes by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die.
1.1.1Coextruded composite drain, waste, and vent pipe, DWV, by definition, is permitted to be produced with two or more layers. The outer layer shall be ABS. The middle layer is permitted to be thermally foamed PVC or solid PVC or a blend of rework material, as specified in the rework material section. The inner layer is permitted to be solid PVC or ABS, or a blend of rework material as specified in the rework material section.
1.1.2The function of this specification is to provide standardization of product, technical data, and serve as a purchasing guide.
1.2 DWV is permitted to be produced utilizing a two layer or three layer coextrusion die.
1.3Materials that do not meet the requirements of the material section are excluded.
1.4Pipe produced to this specification is permitted to be joined using molded fittings meeting the requirements of Specification D2661 or Specification F628. The fitting patterns must comply with Specification D3311.
1.5Pipe produced to this specification is permitted to be perforated in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.6Pipe produced to this specification is permitted to be belled for joining by solvent cementing or belled for joining by an elastomeric seal (gasket), in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.7Recommendations for storage, joining, and installation are provided in Appendix X1, Appendix X2, and Appendix X3, respectively.
1.8The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.9The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
Note 1:Specifications related to this specification are as follows: Specifications D2661, D2665, F628, and F891.
1.10The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.11This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.12This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 122 : 2017 : REDLINE | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM F 891 : 2016 : REDLINE | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core |
| ASTM E 105 : 2016 : REDLINE | Standard Practice for Probability Sampling of Materials |
| ASTM D 3311 : 2017 : REDLINE | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 3965 : 2016 : REDLINE | Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings |
| FED-STD-123 Revision H:2007 | MARKING FOR SHIPMENT (CIVIL AGENCIES) |
| ASTM D 696 : 2016 : REDLINE | Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer |
| ASTM D 2444 : 1999 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2665 : 2014 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ANSI Z34.2 : 1987 | CERTIFICATION - SELF-CERTIFICATION BY PRODUCER OR SUPPLIER |
| ANSI Z34.1 : 1993 | CERTIFICATION - THIRD-PARTY CERTIFICATION PROGRAMS FOR PRODUCTS, PROCESSES, AND SERVICES |
| ASTM D 1784 : 2011 : REDLINE | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.