• There are no items in your cart

ASTM D 696 : 2016 : REDLINE

Current

Current

The latest, up-to-date edition.

Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer

Available format(s)

PDF

Language(s)

English

Published date

01-04-2016

CONTAINED IN VOL. 08.01, 2017 Includes determination of the coefficient of linear thermal expansion for plastic materials having coefficients of expansion greater than 1[mu]m/(m. degrees C) by use of a vitreous silica dilatometer.

1.1This test method covers determination of the coefficient of linear thermal expansion for plastic materials having coefficients of expansion greater than 1 µm/(m.°C) by use of a vitreous silica dilatometer. At the test temperatures and under the stresses imposed, the plastic materials shall have a negligible creep or elastic strain rate or both, insofar as these properties would significantly affect the accuracy of the measurements.

1.1.1Test Method E228 shall be used for temperatures other than −30°C to 30°C.

1.1.2This test method shall not be used for measurements on materials having a very low coefficient of expansion (less than 1 µm/(m.°C). For materials having very low coefficient of expansion, interferometer or capacitance techniques are recommended.

1.1.3Alternative technique commonly used for measuring this property is thermomechanical analysis as described in Test Method E831, which permits measurement of this property over a scanned temperature range.

1.2The thermal expansion of a plastic is composed of a reversible component on which are superimposed changes in length due to changes in moisture content, curing, loss of plasticizer or solvents, release of stresses, phase changes and other factors. This test method is intended for determining the coefficient of linear thermal expansion under the exclusion of these factors as far as possible. In general, it will not be possible to exclude the effect of these factors completely. For this reason, the test method can be expected to give only an approximation to the true thermal expansion.

1.3The values stated in SI units are to be regarded as standard. The values in parentheses are for information only.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:There is no known ISO equivalent to this standard.

Committee
D 20
DocumentType
Redline
Pages
6
PublisherName
American Society for Testing and Materials
Status
Current

MIL-C-47224 Revision B:1993 COMPOUND, MOLDING, TRANSFER, EPOXY RESIN, SINGLE COMPONENT
PREN 13491 : DRAFT 2016 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES
16/30338114 DC : 0 BS EN 13361 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS
CSA S807 : 2010 SPECIFICATION FOR FIBRE-REINFORCED POLYMERS
MIL-PRF-5425 Revision E:1998 PLASTIC SHEET, ACRYLIC, HEAT RESISTANT
16/30338123 DC : 0 BS EN 16993 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF STORAGE LAGOONS, SECONDARY CONTAINMENT (ABOVE AND BELOW GROUND) AND OTHER CONTAINMENT APPLICATIONS FOR CHEMICALS, POLLUTED WATER AND PRODUCED LIQUIDS
13/30290552 DC : 0 BS EN 4691-1 AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION
12/30267857 DC : 0 BS EN 15382 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE
12/30267848 DC : 0 BS EN 13362 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS
ASTM D 5476 : 1999 Standard Classification System for Thermoplastic Polyurethane Materials (TPU) (Withdrawn 2005)
16/30338304 DC : 0 BS ISO/ASTM 52903-1 - ADDITIVE MANUFACTURING - STANDARD SPECIFICATION FOR MATERIAL EXTRUSION BASED ADDITIVE MANUFACTURING OF PLASTIC MATERIALS - PART 1: FEEDSTOCK MATERIALS
ASTM F 942 : 2002 Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
MIL-P-46185 Base Document:1983 PLASTIC MOLDING & EXTRUSION MATERIALS, POLYETHERSULFONE
ASTM F 1876 : 1998 Standard Specification for Polyetherketoneetherketoneketone (PEKEKK) Resins for Surgical Implant Applications
ASTM E 228 : 2017 : REDLINE Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
MIL P 8184 : E PLASTIC SHEET, ACRYLIC, MODIFIED
API 17U : 2015 RECOMMENDED PRACTICE FOR WET AND DRY THERMAL INSULATION OF SUBSEA FLOWLINES AND EQUIPMENT
UNE-EN 13491:2013 Geosynthetic barriers - Characteristics required for use as a fluid barrier in the construction of tunnels and associated underground structures
SAE J 1568 : 2012 MATERIALS FOR PLASTIC PISTONS FOR HYDRAULIC DISC BRAKE CYLINDERS
BS EN 13493:2013 Geosynthetic barriers. Characteristics required for use in the construction of solid waste storage and disposal sites
UNE-EN 15382:2013 Geosynthetic barriers - Characteristics required for use in transportation infrastructure
BS EN 15382:2013 Geosynthetic barriers. Characteristics required for use in transportation infrastructure
EN 13491:2018 Geosynthetic barriers - Characteristics required for use in the construction of tunnels and associated underground structures
ASTM D 3105 : 2017 : REDLINE Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM F 942 : 2002 : R2008 Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
BS EN 13492:2013 Geosynthetic barriers. Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment
BS EN 1770:1998 Products and systems for the protection and repair of concrete structures. Test methods. Determination of the coefficient of thermal expansion
DIN EN 13492:2013-11 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT
DIN EN 15382:2013-11 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE
MIL-P-46120 Revision B:1983 PLASTIC MOLDING AND EXTRUSION MATERIAL POLYSULFONE
MIL-P-46179 Revision A:1986 PLASTIC MOLDING AND EXTRUSION MATERIAL, POLYAMIDE IMIDE
I.S. EN ISO 14692-2:2017 PETROLEUM AND NATURAL GAS INDUSTRIES - GLASS-REINFORCED PLASTICS (GRP) PIPING - PART 2: QUALIFICATION AND MANUFACTURE (ISO 14692-2:2017)
CSA S808 : 2014 SPECIFICATION FOR FIBRE-REINFORCED POLYMER (FRP) MATERIALS FOR EXTERNALLY REINFORCING STRUCTURES
SAE J 2253 : 2017 TEST PROCEDURES FOR AUTOMOTIVE STRUCTURAL COMPOSITE MATERIALS
MIL P 5425 : D PLASTIC, SHEET, ACRYLIC, HEAT RESISTANT
ASTM E 289 : 2017 : REDLINE Standard Test Method for Linear Thermal Expansion of Rigid Solids with Interferometry
DIN EN 15382 E : 2013 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE
CSA S807 : 2010 : R2015 SPECIFICATION FOR FIBRE-REINFORCED POLYMERS
12/30267851 DC : 0 BS EN 13491 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES
MIL-I-16923 Revision H:1991 INSULATING COMPOUND, ELECTRICAL, EMBEDDING, EPOXY
MIL-PRF-8184 Revision F:1998 PLASTIC SHEET, ACRYLIC MODIFIED
ASTM F 635 : 1985 : R1991 Guide for Selection of Tests for Material Properties of Liquid Thermoset Encapsulating Compounds for Electronic and Microelectronic Encapsulation (Withdrawn 1996)
ASTM D 7793 : 2017 : REDLINE Standard Specification for Insulated Vinyl Siding
UNI CEN ISO/TS 24817 : 2011 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
UNI 11489 : 2013 GEOSYNTHETIC BARRIERS - POLYMERIC GEOSYNTHETICS MADE OF PLASTIFIED POLYVINILCLORIDE - CHARACTERISTICS AND ACCEPTANCE LIMITS
PREN 4691-1 : DRAFT 2015 AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION
EN 4691-1:2017 Aerospace series - Tie rod with integrated bolts - Part 1: Technical specification
DIN EN 13361:2016-08 (Draft) GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS
DIN EN 13491:2016-08 (Draft) GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES
DIN EN 13492:2016-08 (Draft) GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT
ASTM F 790 : 2008 : R2013 Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures
ASTM D 7031 : 2011 : REDLINE GUIDE FOR EVALUATING MECHANICAL AND PHYSICAL PROPERTIES OF WOOD-PLASTIC COMPOSITE PRODUCTS
PREN 13362 : DRAFT 2012 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS
ASTM D 6455 : 2011 Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGM)
ASTM D 5140 : 1995 Standard Guide for Testing Polyurethane "Poured in Place" Thermal Break Materials (Withdrawn 2004)
I.S. EN 13361:2018 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS
DIN EN 13493:2016-08 (Draft) GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES
DIN EN 13361:2013-11 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS
ISO/TS 24817:2006 Petroleum, petrochemical and natural gas industries Composite repairs for pipework Qualification and design, installation, testing and inspection
ASME PCC 2 : 2015 REPAIR OF PRESSURE EQUIPMENT AND PIPING
ASME B31.8 : 2016 Gas Transmission and Distribution Piping Systems
L-C-530 Revision C:1987 COATING, PIPE, THERMOPLASTIC RESIN
DD CEN ISO/TS 24817:2011 Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection
ASTM F 1499 : 2017 : REDLINE Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
EN 16994:2018 Clay Geosynthetic Barriers - Characteristics required for use in the construction of underground structures (other than tunnels and associated structures)
BS EN 16994:2018 Clay Geosynthetic Barriers. Characteristics required for use in the construction of underground structures (other than tunnels and associated structures)
MIL-DTL-32265 Base Document:2007 Folded Fiberglass Mat Fabrication and Packaging
ASTM F 790 : 2008 Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures
ASTM F 1579 : 2002 Standard Specification for Polyaryletherketone (PAEK) Polymers for Surgical Implant Applications
ISO 24817:2017 Petroleum, petrochemical and natural gas industries — Composite repairs for pipework — Qualification and design, installation, testing and inspection
ASTM F 942 : 2002 : R2013 Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
UNI 11498 : 2013 GEOSYNTHETIC BARRIERS - STRUCTURED POLYMERIC GEOSYNTHETICS MADE OF HIGH AND MEDIUM DENSITY POLYETHYLENE - CHARACTERISTICS AND ACCEPTANCE LIMITS
I.S. EN 4691-1:2017 AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION
BS EN ISO 24817:2017 Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection
EN 13493:2018 Geosynthetic barriers - Characteristics required for use in the construction of solid waste storage and disposal sites
I.S. EN 13491:2018 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES
DIN EN 13362:2016-08 (Draft) GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS
ASTM D 3679 : 2017 : REDLINE Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
I.S. EN ISO 24817:2017 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION (ISO 24817:2017, CORRECTED VERSION 2018-01-01)
ASTM D 3841 : 2016 : REDLINE Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels
ASTM D 4477 : 2016 : REDLINE Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit
ASTM C 1355/C1355M : 1996 : R2011 Standard Specification for Glass Fiber Reinforced Gypsum Composites
UNI 11494 : 2013 GEOSYNTHETIC BARRIERS - POLYMERIC GEOSYNTHETICS MADE OF POLYOLEFINS (TPO-FPO) - CHARACTERISTICS AND ACCEPTANCE LIMITS
ISO 14692-2:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 2: Qualification and manufacture
NASA KSC SPEC E 0029 : 1972 COMPOUND, POTTING AND MOLDING ELASTOMERIC, SPECIFICATION FOR
CSA S806: 2012 DESIGN AND CONSTRUCTION OF BUILDING STRUCTURES WITH FIBRE-REINFORCED POLYMERS
S806-12 (R2017) Design and construction of building structures with fibre-reinforced polymers
SAE AMS 3732 : 2015 POTTING COMPOUND, EPOXY ONE PART, FILLED, HEAT CURE, LOW CTE
16/30338108 DC : DRAFT JULY 2016 BS EN 13362 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS
12/30267854 DC : 0 BS EN 13492 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN CONSTRUCTION AND TUNNELS AND ASSOCIATED UNDER GROUND STRUCTURES
12/30267845 DC : 0 BS EN 13361 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS
ASTM C 1355/C1355M : 1996 Standard Specification for Glass Fiber Reinforced Gypsum Composites
16/30338117 DC : 0 BS EN 13493 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES
IEEE 1133-1988 IEEE Application Guide for Evaluating Nonceramic Materials for High-Voltage Outdoor Applications
MIL-C-24449 Revision A:1981 CAST POLYMETHYL METHACRYLATE FOR SHEET STOCK, CUSTOM CASTINGS AND FINISHED WINDOWS
ASTM F 1876 : 1998 : R2003 : EDT 1 Standard Specification for Polyetherketoneetherketoneketone (PEKEKK) Resins for Surgical Implant Applications (Withdrawn 2012)
ASTM D 4098 : 1982 : R1987 : EDT 1 Practice for Evaluating High-Density Rigid Cellular Thermosets (Withdrawn 1994)
12/30268279 DC : 0 BS EN 13493 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES
ASTM C 1355/C1355M : 1996 : R2006 Standard Specification for Glass Fiber Reinforced Gypsum Composites
PREN 13493 : DRAFT 2016 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES
PREN 13492 : DRAFT 2016 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT
MIL-PRF-24793 Revision A:2001 Adhesive, UV Curable, One Part, Fiber Optics
14/30256269 DC : 0 BS EN ISO 24817 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
ADS-13F-HDBK : 1997 AERONAUTICAL DESIGN STANDARD - HANDBOOK - AIR VEHICLE MATERIALS AND PROCESSES
DD ISO/TS 24817 : 2006 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
L-P-504 Revision E:1991 PLASTIC SHEET AND FILM, CELLULOSE ACETATE
ASTM F 2820 : 2012 Standard Specification for Polyetherketoneketone (PEKK) Polymers for Surgical Implant Applications
I.S. EN 16994:2018 CLAY GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF UNDERGROUND STRUCTURES (OTHER THAN TUNNELS AND ASSOCIATED STRUCTURES)
UNE-EN 13361:2013 Geosynthetic barriers - Characteristics required for use in the construction of reservoirs and dams
UNE-EN 13362:2013 Geosynthetic barriers - Characteristics required for use in the construction of canals
EN 13362:2018 Geosynthetic Barriers - Characteristics required for use in the construction of canals
ASTM D 5593 : 1999 : EDT 1 Standard Classification for Thermoplastic Elastomers-Olefinic (TEO) (Withdrawn 2005)
ASTM D 6455 : 2011 : R2018 Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGMs)
ASTM F 1579 : 2002 : EDT 1 Standard Specification for Polyaryletherketone (PAEK) Polymers for Surgical Implant Applications (Withdrawn 2011)
ASTM D 3678 : 2014 : REDLINE Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions
EN 15382:2018 Geosynthetic barriers - Characteristics required for use in transportation infrastructure
ASTM F 2021 : 2017 : REDLINE Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems
EN 13492:2018 Geosynthetic barriers - Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment
EN ISO 14692-2:2017 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2017)
EN 13361:2018 Geosynthetic barriers - Characteristics required for use in the construction of reservoirs and dams
ASTM C 1355/C1355M : 1996 : R2001 Standard Specification for Glass Fiber Reinforced Gypsum Composites
I.S. EN 13493:2013 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES
I.S. EN 15382:2013 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE
I.S. EN 13362:2018 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS
11/30242263 DC : 0 BS EN 4691-001 - AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - TECHNICAL SPECIFICATION
BS EN 4691-1:2017 Aerospace series. Tie rod with integrated bolts Technical specification
PREN 13361 : DRAFT 2016 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS
ASTM F 636 : 1985 : R1991 Guide for Selection of Tests for Material Properties of Transfer Molding Compounds for Electronic and Microelectronic Encapsulation (Withdrawn 1996)
16/30338126 DC : 0 BS EN 13492 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT
16/30338105 DC : 0 BS EN 16994 - CLAY GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF UNDERGROUND STRUCTURES (OTHER THAN TUNNELS AND ASSOCIATED STRUCTURES)
UNE-EN 13492:2013 Geosynthetic barriers - Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment
MIL P 008184 : D PLASTIC SHEET, ACRYLIC, MODIFIED
SAE AMS 3731 : 2016 POTTING COMPOUND, EPOXY, BISPHENOL A-TYPE
I.S. EN 13492:2013 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT
16/30338111 DC : 0 BS EN 13491 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES
ASTM D 710 : 2013 : REDLINE Standard Specification for Vulcanized Fibre Sheets, Rods, and Tubes Used for Electrical Insulation
16/30338120 DC : 0 BS EN 15382 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE
UNE-EN 13493:2013 Geosynthetic barriers - Characteristics required for use in the construction of solid waste storage and disposal sites
MIL-R-47025 Revision A:1991 RESIN, CASTING, FIRE RETARDANT, EPOXY BASE
A500-16 Building guards
ACI 440.2R : 2017 GUIDE FOR THE DESIGN AND CONSTRUCTION OF EXTERNALLY BONDED FRP SYSTEMS FOR STRENGTHENING CONCRETE STRUCTURES
ISO/TR 15655:2003 Fire resistance Tests for thermo-physical and mechanical properties of structural materials at elevated temperatures for fire engineering design
DIN EN 15382:2016-08 (Draft) GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE
UNI 11309 : 2008 GEOSYNTHETIC BARRIERS - POLYMERIC GEOSYNTHETICS MADE OF HIGH AND MEDIUM DENSITY POLIETHYLEN - CHARACTERISTICS AND ACCEPTANCE LIMITS
API TR 17TR8 : 2018 HIGH-PRESSURE HIGH-TEMPERATURE DESIGN GUIDELINES
BS EN 13362:2018 Geosynthetic Barriers. Characteristics required for use in the construction of canals
CSA C22.2 No. 126 : 0 CABLE TRAY SYSTEMS
ASTM C 1355/C1355M : 1996 : R2015 Standard Specification for Glass Fiber Reinforced Gypsum Composites
ASTM D 7445 : 2018 : REDLINE Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)
ASTM E 1420 : 1991 Practice for Specifying Polymeric Materials for Service in Ionizing Radiation Environments (Withdrawn 1996)
ASTM D 7745 : 2011 Standard Practice for Testing Pultruded Composites
S.R. CEN ISO TS 24817:2011 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
DIN EN 13362:2013-11 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS
DIN EN 13493:2013-11 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES
CEN ISO/TS 24817:2011 Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection (ISO/TS 24817:2006)
ASME RTP 1 : 2015 REINFORCED THERMOSET PLASTIC CORROSION-RESISTANT EQUIPMENT
ASME RTP-1 : 2017 REINFORCED THERMOSET PLASTIC CORROSION-RESISTANT EQUIPMENT
ASME PVHO 1 : 2016 SAFETY STANDARD FOR PRESSURE VESSELS FOR HUMAN OCCUPANCY

ASTM E 228 : 2017 : REDLINE Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM D 4065 : 2012 : REDLINE Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures

View more information
€69.98
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.