ASTM F 2328 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts
Hardcopy , PDF
10-12-2022
English
21-09-2017
Committee |
F 16
|
DocumentType |
Test Method
|
Pages |
4
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered inch series steel bolts, screws, studs, nuts, and similar parts which have been heated to facilitate fabrication or to modify their mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results.
1.2Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburization—the optical method and the microindentation method 1. Either method is appropriate for routine examinations. The microindentation method 2 shall be considered the referee method.
1.3For the purpose of these tests, there are four classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties.
1.4The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F 2882/F2882M : 2017 | Standard Specification for Screws, Alloy Steel, Heat Treated, 170 ksi and 1170 MPa Minimum Tensile Strength (Inch and Metric) |
ASTM F 3043 : 2015 | Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Alloy Steel, Heat Treated, 200 ksi Minimum Tensile Strength |
ASTM A 574 : 2017 | Standard Specification for Alloy Steel Socket-Head Cap Screws |
ASTM F 3148 : 2017 : REV A | Standard Specification for High Strength Structural Bolt Assemblies, Steel and Alloy Steel, Heat Treated, 144ksi Minimum Tensile Strength, Inch Dimensions |
ASTM F 3111 : 2016 | Standard Specification for Heavy Hex Structural Bolt/Nut/Washer Assemblies, Alloy Steel, Heat Treated, 200 ksi Minimum Tensile Strength |
ASTM F 912 : 2011 : R2017 | Standard Specification for Alloy Steel Socket Set Screws |
ASTM F 606/F606M : 2016 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
ASTM A 962/A962M : 2018 | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM A 354 : 2017 : EDT 2 | Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners |
ASTM F 3125/F3125M : 2018 | Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength |
ASTM F 835 : 2020 | Standard Specification for Alloy Steel Socket Button and Flat Countersunk Head Cap Screws |
ASTM F 606/F606M : 2021 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
ASTM A 574 : 2021 | Standard Specification for Alloy Steel Socket-Head Cap Screws |
ASTM A 962/A962M : 2022 | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM F 3125/F3125M : 2022 | Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength |
ASTM F 1789 : 2014 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2016 | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2017 | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2008 | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2006 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2001 : REV A | Standard Terminology of F16 Mechanical Fasteners |
ASTM F 1789 : 2017 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2012 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2001 : REV B | Standard Terminology of F16 Mechanical Fasteners |
ASTM F 1789 : 2005 : REV C | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2022 | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2003 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM E 384 : 2022 | Standard Test Method for Microindentation Hardness of Materials |
ASTM F 1789 : 2008 : REV B | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2006 : REV B | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2014 | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2002 : REV A | Standard Terminology of F16 Mechanical Fasteners |
ASTM F 1789 : 2009 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2006 : REV C | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2004 : REV B | Standard Terminology for F16 Mechanical Fasteners |
ASTM E 384 : 2011 | Standard Test Method for Knoop and Vickers Hardness of Materials |
ASTM F 1789 : 2007 : REV C | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2007 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2008 : REV C | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2015 | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2002 : REV B | Standard Terminology of F16 Mechanical Fasteners |
ASTM F 1789 : 2010 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2012 | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2005 : REV D | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2017 : REV A : EDT 1 | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2010 : REV B | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2010 : REV A : EDT 1 | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2015 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2000 : REV A | Standard Terminology of F16 Mechanical Fasteners |
ASTM F 1789 : 2007 : REV B | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2011 : REV B | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2004 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2005 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2008 : REV D | Standard Terminology for F16 Mechanical Fasteners |
ASTM E 384 : 2017 | Standard Test Method for Microindentation Hardness of Materials |
ASTM F 1789 : 2007 | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2008 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2011 : REV A | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2005 : REV B | Standard Terminology for F16 Mechanical Fasteners |
ASTM F 1789 : 2002 | Standard Terminology of F16 Mechanical Fasteners |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.