ASTM F 2363/F2363M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Sewage and Graywater Flow Through Treatment Systems
Hardcopy , PDF
10-02-2023
English
18-12-2017
Committee |
F 25
|
DocumentType |
Standard
|
Pages |
17
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers the design, manufacture, performance, operation, and testing of flow through treatment systems intended to process sewage or graywater, or both, generated during a ship's normal service. This specification is intended for use by designers, manufacturers, purchasers, and operators of shipboard environmental pollution control equipment to determine the requirements for equipment design, manufacture, purchase, and in-service operation.
1.2The treatment system shall be capable of meeting the effluent requirements detailed in Section 4 with respect to a ship's operational area.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F 1030 : 1986 : R2018 | Standard Practice for Selection of Valve Operators |
ASTM E 11 : 2020 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM F 1510 : 1998 | Standard Specification for Rotary Positive Displacement Pumps, Commercial Ships Use |
ASTM F 1030 : 1986 : R2004 | Standard Practice for Selection of Valve Operators |
ASTM F 2044 : 2009 | Standard Specification for Liquid Level Indicating Equipment, Electrical |
ASTM D 1253 : 1986 : R1996 | Standard Test Method for Residual Chlorine in Water |
ASTM F 1511 : 2011 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 1511 : 2004 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 1122 : 1987 : R1992 | Standard Specification for Quick Disconnect Couplings |
ASTM A 307 : 2014 : EDT 1 | Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength |
ASTM D 1253 : 2003 | Standard Test Method for Residual Chlorine in Water |
ASTM F 1098 : 1987 : R2004 | Standard Specification for Envelope Dimensions for Butterfly Valves-NPS 2 to 24 |
ASTM F 1323 : 2001 | Standard Specification for Shipboard Incinerators |
ASTM F 1030 : 1986 : R1998 | Standard Practice for Selection of Valve Operators |
ASTM F 1387 : 1993 : R1998 | Standard Specification for Performance of Mechanically Attached Fittings |
ASTM F 998 : 2012 : R2022 | Standard Specification for Centrifugal Pump, Shipboard Use |
ASTM F 1098 : 1987 : R2015 | Standard Specification for Envelope Dimensions for Butterfly Valves—NPS 2 to 24 |
ASTM F 1510 : 2007 : R2019 | Standard Specification for Rotary Positive Displacement Pumps, Ships Use |
ASTM F 1510 : 2001 : R2006 | Standard Specification for Rotary Positive Displacement Pumps, Commercial Ships Use |
ASTM F 2044 : 2009 : R2019 : EDT 1 | Standard Specification for Liquid Level Indicating Equipment, Electrical |
ASTM F 1511 : 2014 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 998 : 2012 : R2018 | Standard Specification for Centrifugal Pump, Shipboard Use |
ASTM D 1253 : 2014 | Standard Test Method for Residual Chlorine in Water |
ASTM F 1155 : 2010 : R2019 | Standard Practice for Selection and Application of Piping System Materials |
ASTM F 1098 : 1987 : R1998 | Standard Specification for Envelope Dimensions for Butterfly Valves-NPS 2 to 24 |
ASTM F 1511 : 2005 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 1166 : 2021 | Standard Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities<rangeref></rangeref > |
ASTM F 1298 : 1990 : R1995 : EDT 1 | Standard Specification for Flexible, Expansion-Type Ball Joints for Marine Applications |
ASTM F 1511 : 2006 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 1098 : 1987 : R2019 | Standard Specification for Envelope Dimensions for Butterfly Valves—NPS 2 to 24 |
ASTM F 993 : 2021 | Standard Specification for Valve Locking Devices |
ASTM F 992 : 2017 | Standard Specification for Valve Label Plates |
ASTM F 1511 : 1998 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 1323 : 1998 | Standard Specification for Shipboard Incinerators |
ASTM F 1511 : 2013 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM F 1155 : 1998 | Standard Practice for Selection and Application of Piping System Materials |
ASTM F 1122 : 2022 | Standard Specification for Quick Disconnect Couplings (6 in. NPS and Smaller) |
ASTM F 993 : 1986 : R1996 : EDT 1 | Standard Specification for Valve Locking Devices |
ASTM F 2044 : 2000 | Standard Specification for Liquid Level Indicating Equipment, Electrical (Withdrawn 2009) |
ASTM F 1387 : 1999 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
ASTM F 1387 : 1999 : R2012 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
ASTM F 1510:2001 | Standard Specification for Rotary Positive Displacement Pumps, Commercial Ships Use |
ASTM F 1030 : 1986 : R2014 : EDT 1 | Standard Practice for Selection of Valve Operators |
ASTM F 992 : 1986 : R1996 : EDT 1 | Standard Specification for Valve Label Plates |
ASTM F 1323 : 2014 | Standard Specification for Shipboard Incinerators |
ASTM F 1166 : 1995 : REV A : R2006 | Standard Practice for Human Engineering Design for Marine Systems, Equipment and Facilities |
ASTM F 1511 : 2002 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 1387 : 2019 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
ASTM F 992 : 2017 : R2022 | Standard Specification for Valve Label Plates |
ASTM F 1298 : 1990 : R2018 | Standard Specification for Flexible, Expansion-Type Ball Joints for Marine Applications |
ASTM F 1511 : 2009 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 1298 : 1990 : R2001 | Standard Specification for Flexible, Expansion-Type Ball Joints for Marine Applications |
ASTM A 563 : 2015 | Standard Specification for Carbon and Alloy Steel Nuts |
ASTM D 1253 : 2008 | Standard Test Method for Residual Chlorine in Water |
ASTM F 993 : 2017 | Standard Specification for Valve Locking Devices |
ASTM F 1511 : 2003 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 1122 : 2004 : R2010 | Standard Specification for Quick Disconnect Couplings (6 in. NPS and Smaller) |
ASTM F 1098 : 1987 : R2010 | Standard Specification for Envelope Dimensions for Butterfly Valves-NPS 2 to 24 |
ASTM F 1166 : 2007 : R2013 | Standard Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities |
ASTM F 1387 : 1999 : R2005 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
ASTM D 1253 : 2014 : R2021 : EDT 1 | Standard Test Method for Residual Chlorine in Water |
ASTM F 1298 : 1990 : R2012 | Standard Specification for Flexible, Expansion-Type Ball Joints for Marine Applications |
ASTM F 1511 : 2016 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 998 : 2000 | Standard Specification for Centrifugal Pump, Shipboard Use |
ASTM F 1155 : 2010 : R2015 | Standard Practice for Selection and Application of Piping System Materials |
ASTM F 1122 : 2004 : R2021 | Standard Specification for Quick Disconnect Couplings (6 in. NPS and Smaller) |
ASTM F 1511 : 2018 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM F 1510 : 2007 | Standard Specification for Rotary Positive Displacement Pumps, Ships Use |
ASTM F 1166 : 2007 | Standard Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities |
ASTM F 2044 : 2009 : R2013 | Standard Specification for Liquid Level Indicating Equipment, Electrical |
ASTM F 1298 : 1990 : R2006 | Standard Specification for Flexible, Expansion-Type Ball Joints for Marine Applications |
ASTM F 1510 : 2007 : R2013 | Standard Specification for Rotary Positive Displacement Pumps, Ships Use |
ASTM F 1122 : 2004 : R2015 : EDT 1 | Standard Specification for Quick Disconnect Couplings (6 in. NPS and Smaller) |
ASTM F 1155 : 2010 | Standard Practice for Selection and Application of Piping System Materials |
ASTM A 307 : 2021 | Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength |
ASTM F 1166 : 1995 : REV A : R2000 | Standard Practice for Human Engineering Design for Marine Systems, Equipment and Facilities |
ASTM F 1122 : 2004 | Standard Specification for Quick Disconnect Couplings (6 in. NPS and Smaller) |
ASTM F 1323 : 2008 | Standard Specification for Shipboard Incinerators |
ASTM F 1030 : 1986 : R2008 | Standard Practice for Selection of Valve Operators |
ASTM F 1323 : 2014 : R2020 | Standard Specification for Shipboard Incinerators |
ASTM F 1511 : 2007 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.