ASTM F 2473 : 2012 : R2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Performance of Water-Bath Rethermalizers
Hardcopy , PDF
21-07-2023
English
13-03-2018
CONTAINED IN VOL. 15.08, 2018 Specifies the energy consumption and rethermalizing performance of floor-model and countertop water-bath rethermalizers.
Committee |
F 26
|
DocumentType |
Test Method
|
Pages |
12
|
ProductNote |
Reconfirmed 2018
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers the energy consumption and rethermalizing performance of floor-model and countertop water-bath rethermalizers. The food service operator can use this evaluation to select a water-bath rethermalizer and understand its energy consumption and production capacity.
1.2This test method is applicable to floor and countertop model gas and electric units.
1.3The water-bath rethermalizer can be evaluated with respect to the following (where applicable):
1.3.1Energy input rate (10.2),
1.3.2Preheat energy consumption, time, and rate (10.4),
1.3.3Idle energy rate (10.5),
1.3.4Pilot energy rate (10.6),
1.3.5Retherm energy rate (10.8),
1.3.6Production capacity (10.8), and
1.3.7Retherm-energy efficiency (10.8).
1.4This test method is not intended to answer all performance criteria in the evaluation and selection of a water-bath rethermalizer.
1.5The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F 2875 : 2010 : R2020 | Standard Guide for Laboratory Requirements Necessary to Test Commercial Cooking and Warming Appliances to ASTM Test Methods |
ASTM F 2875 : 2010 : R2015 | Standard Guide for Laboratory Requirements Necessary to Test Commercial Cooking and Warming Appliances to ASTM Test Methods |
ASTM F 2916 : 2019 | Standard Practice for Environmental Impact Analysis of Commercial Food Service Equipment |
NSF FOOD EQUIPMENT : 2005 | NSF PRODUCT LISTINGS OF FOOD EQUIPMENT AND RELATED PRODUCTS, COMPONENTS AND MATERIALS |
ASTM D 3588 : 1998 : R2017 : EDT 1 | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels |
ASTM D 3588 : 1998 : R2017 | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels |
ASTM D 3588 : 1998 | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels |
ASHRAE HDBK FUNDAMENTALS : 2013 | ASHRAE HANDBOOK - FUNDAMENTALS |
NSF 4 : 2016 | COMMERCIAL COOKING, RETHERMALIZATION, AND POWERED HOT FOOD HOLDING AND TRANSPORTATION EQUIPMENT |
ASTM D 3588 : 1998 : R2003 | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels |
ASTM D 3588 : 1998 : R2011 | Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels |
CSA/ANSI Z83.11 : 2016 | GAS FOOD SERVICE EQUIPMENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.