ASTM F 2619/F2619M : 2013 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for High-Density Polyethylene (PE) Line Pipe
15-04-2020
English
01-12-2013
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.04, 2017 Defines requirements and test methods for high-density polyethylene (PE) materials, pipe and fittings for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water.
| Committee |
F 17
|
| DocumentType |
Redline
|
| Pages |
15
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers requirements and test methods for high-density polyethylene (PE) materials, pipe and fittings for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.
1.1.1For the purposes of this specification, high-density polyethylene material is Specification D3350 density cell classification 3 or higher. This specification does not cover materials having Specification D3350 density cell classification less than 3 such as medium or low density polyethylene materials.
1.1.2See Specification D2513 for polyethylene pipe and fittings intended for use in the distribution of natural gas, or for use with liquefied petroleum gas.
1.2Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| API 15S : 2016 | SPOOLABLE REINFORCED PLASTIC LINE PIPE |
| ASTM F 2896 : 2011 : R2017 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| AWWA C906:2015 | POLYETHYLENE (PE) PRESSURE PIPE AND FITTINGS, 4 IN. THROUGH 65 IN. (100 MM THROUGH 1,650 MM), FOR WATERWORKS |
| ASTM D 2513 : 2017-01 | SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS |
| ASTM F 2807 : 2013 | Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications |
| ASTM F 2905/F2905M : 2013 | Standard Specification for Black Crosslinked Polyethylene (PEX) Line Pipe, Fittings and Joints For Oil and Gas Producing Applications |
| ASTM F 2807 : 2013 : R2018 | Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications (Withdrawn 2024) |
| ASTM F 2896 : 2011 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| ASTM D 3261 : 2016-11 | SPECIFICATION FOR BUTT HEAT FUSION POLYETHYLENE (PE) PLASTIC FITTINGS FOR POLYETHYLENE (PE) PLASTIC PIPE AND TUBING |
| ASTM D 1238 : 2013 : REDLINE | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| CAN/CSA-Z662-15 | Oil and gas pipeline systems |
| PPI TR 3 : 2017 | POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE |
| CFR 49(PTS186-199) : 0 | TRANSPORTATION |
| PPI TR 4 : 2017 | HDB/HDS/SDB/PDB/MRS LISTED MATERIALS - PPI LISTING OF HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESS (HDS), STRENGTH DESIGN BASIS (SDB), PRESSURE DESIGN BASIS (PDB) AND MINIMUM REQUIRED STRENGTH (MRS) RATINGS FOR THERMOPLASTIC PIPING MATERIALS OR PIPE |
| ASTM D 2683 : 2014 : REDLINE | Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing |
| ASTM D 1603 : 2014 : REDLINE | Standard Test Method for Carbon Black Content in Olefin Plastics |
| ASTM D 2513 : 2017-01 | SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS |
| FED-STD-123 Revision H:2007 | MARKING FOR SHIPMENT (CIVIL AGENCIES) |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 1055 : 2016-09 | SPECIFICATION FOR ELECTROFUSION TYPE POLYETHYLENE FITTINGS FOR OUTSIDE DIAMETER CONTROLLED POLYETHYLENE AND CROSSLINKED POLYETHYLENE (PEX) PIPE AND TUBING |
| ASTM D 2290 : 2016-12 | TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE |
| ASTM D 3350 : 2014 : REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.