![header thumbnail](/images/publishers\astm_cover.gif)
ASTM F 2881/F2881M : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications
Hardcopy , PDF
10-06-2021
English
24-04-2019
This specification covers test methods and requirements for dual wall polypropylene pipe and fittings.
Committee |
F 17
|
DocumentType |
Standard
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers requirements and test methods for dual wall polypropylene pipe and fittings. The nominal inside diameters covered are 12 to 60 in. [300 to 1500 mm].
1.2The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure storm sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.
1.3This specification covers pipe and fittings with an interior smooth wall and an annular corrugated profile outer wall (Fig. 1).
FIG. 1Interior Smooth Wall and an Annular Corrugated Profile Outer Wall
![Interior Smooth Wall and an Annular Corrugated Profile Outer Wall](http://www.astm.org/HTTP/IMAGES/F2881_001517.png)
1.4Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5The following precautionary statement caveat pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2321 : 2005 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 4101 : 2001 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 2321 : 2009 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 1238 : 2000 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 4101 : 2001 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2006 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 1238 : 2004 : REV C | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 4101 : 2005 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3895 : 1998 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
ASTM D 2321 : 2014 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 4101 : 2000 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
ASTM D 4101 : 2008 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2006 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2004 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4218 : 2020 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique |
ASTM D 2444 : 1999 : R2010 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
ASTM D 2444 : 2019 | Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
ASTM D 1238 : 2013 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 4101 : 2014 : EDT 2 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2010 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2011 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3212 : 1996 : REV A : R2003 | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
ASTM D 4101 : 2005 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM F 477 : 2002 | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
ASTM D 3212 : 2007 : R2020 | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
ASTM D 2444 : 2017 | Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
ASTM D 1238 : 2010 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 2412 : 2011 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
ASTM D 3895 : 2007 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
ASTM D 3895 : 2019 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
ASTM D 2412 : 2002 : R2008 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
ASTM D 2321 : 2018 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 4101 : 2007 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3895 : 2006 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
ASTM D 2321 : 2011 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 4101 : 2002 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3895 : 2003 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
ASTM D 4218 : 1996 : R2001 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique |
ASTM D 4101 : 2003 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 2412 : 2010 : REV A | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
ASTM D 2321 : 2000 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 4101 : 2002 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 1505 : 2003 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2990 : 2017 | Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
ASTM D 4218 : 1996 : R2008 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique |
ASTM D 3212 : 2007 : R2013 | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
ASTM D 2444 : 2021 | Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
ASTM D 4101 : 2009 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 4101 : 2006 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3895 : 2014 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2321 : 2004 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 2412 : 1996 : REV A | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
ASTM D 2990 : 2001 | Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
ASTM D 3212 : 2007 | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
ASTM D 4101 : 2004 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 1982 : R1988 : EDT 1 | Standard Specification for Propylene Plastic Injection and Extrusion Materials |
ASTM D 2412 : 2002 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
ASTM D 4101 : 2017 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
ASTM D 2321 : 2014 : EDT 1 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 6992 : 2003 | Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
ASTM D 2321 : 1974 | Recommended Practice for Underground Installation Of Flexible Thermoplastic Sewer Pipe |
ASTM D 2321 : 2004 : EDT 1 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 3212 : 1996 : REV A : R2003 : EDT 1 | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
ASTM D 3895 : 2002 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
ASTM D 6992 : 2016 | Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
ASTM D 3895 : 2004 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
ASTM D 4101 : 2014 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 1238 : 2004 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 2990 : 2009 | Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
ASTM D 2444 : 1999 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
ASTM D 2990 : 1995 | Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
ASTM D 1505 : 1968 : R1979 | Standard Test Method for Density Of Plastics By The Density-Gradient Technique |
ASTM D 2412 : 2021 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
ASTM D 4218 : 2015 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique |
ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
ASTM D 3212 : 1996 : REV A | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
ASTM D 4101 : 2010 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 6992 : 2003 : R2009 | Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
ASTM D 4101 : 2003 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 1505 : 2010 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 2444 : 1999 : R2005 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
ASTM D 1505 : 2018 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 2321 : 2008 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 6992 : 2003 : R2015 | Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
ASTM D 4101 : 2003 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
ASTM D 1505 : 1998 : EDT 1 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
ASTM D 1238 : 2001 : EDT 1 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 4101 : 2002 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 1238 : 2004 : REV A | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 2321 : 2020 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 2412 : 2011 : R2018 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
ASTM D 4101 : 2014 : EDT 1 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 1238 : 1985 | Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 2412 : 2010 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
ASTM D 4218 : 1996 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.