ASTM F 3131 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Epoxy / Cotton Raw Materials for the Use in Bearing Cages
Hardcopy , PDF
17-03-2023
English
28-01-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 01.08, 2017 Defines basic characteristics required for porous laminated Epoxy materials intended for use as instrument and thin-section ball-bearing retainers (cages) and the methods of determining these characteristics.
| Committee |
F 34
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers basic characteristics required for porous laminated Epoxy materials intended for use as instrument and thin-section ball-bearing retainers (cages) and the methods of determining these characteristics.
1.2Forms—Sheets and Rolled Tubes are recommended forms of laminated material covered by this specification.
1.3Intended Use—Materials produced to this specification are intended for use as ball bearing retainers (cages). Temperature range is limited to 284°F (140°C) and below
1.4Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 2257 : 1998 | Standard Test Method for Extractable Matter in Textiles |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 2257 : 1998 : R2004 | Standard Test Method for Extractable Matter in Textiles |
| ASTM E 1640 : 2013 : R2018 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
| ASTM E 1640 : 2009 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
| ASTM E 1640 : 2004 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM E 1640 : 1999 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
| ASTM D 2257 : 2020 | Standard Test Method for Extractable Matter in Textiles |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 2257 : 1998 : R2012 | Standard Test Method for Extractable Matter in Textiles |
| ASTM D 570 : 2022 | Standard Test Method for Water Absorption of Plastics |
| ASTM D 695 : 2015 : REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics |
| ASTM E 1640 : 2013 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
| ASTM D 570 : 1998 : R2018 | Standard Test Method for Water Absorption of Plastics |
| ASTM E 1640 : 2018 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.