ASTM F 3139 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Analysis of Tin-Based Solder Alloys for Minor and Trace Elements Using Inductively Coupled Plasma Atomic Emission Spectrometry
Hardcopy , PDF
09-11-2023
English
15-07-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 10.04, 2015 Describes procedures for the analysis of tin-based solder alloys for minor and trace elements using inductively-coupled plasma atomic emission spectrometry (ICP-AES) instrumentation.
| Committee |
F 40
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers procedures for the analysis of tin-based solder alloys for minor and trace elements using inductively-coupled plasma atomic emission spectrometry (ICP-AES) instrumentation.
1.2These test procedures were validated for the analytes and mass fractions listed below.
| Element | Validated Mass Fraction |
| Lead | 115 to 965 |
| Cadmium | 25 to 60 |
| Mercury | 5 to 530 |
| Antimony | 85 to 1330 |
| Bismuth | 80 to 210 |
| Arsenic | 95 to 360 |
| Silver | 4000 to 42100 |
| Cobalt | 0.5 to 60 |
| Iron | 15 to 115 |
| Chromium | 0.5 to 1.5 |
| Copper | 3000 to 30600 |
| Indium | 25 to 115 |
| Nickel | 5 to 150 |
| Phosphorus | 10 to 110 |
| Selenium | 1 to 30 |
| Zinc | 2 to 160 |
| Aluminum | 1 to 3 |
1.3The procedures appear in the following order:
| Procedure | Section |
| Internal Standardization | 8 |
| Calibration Solution Preparations | 9 |
| Preparation of Sample and Validation Solutions | 10 |
| Calibration | 11 |
| Analysis Procedure | 12 |
1.4The values stated in SI units are to be regarded as the standard. Any other values are for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM E 1479 : 2016 | Standard Practice for Describing and Specifying Inductively Coupled Plasma Atomic Emission Spectrometers |
| ASTM D 1129 : 2013 : REDLINE | Standard Terminology Relating to Water |
| ASTM D 1129 : 2003 | Standard Terminology Relating to Water |
| ASTM E 177 : 2014 : REDLINE | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM E 1479 : 1999 : R2005 | Standard Practice for Describing and Specifying Inductively-Coupled Plasma Atomic Emission Spectrometers |
| ASTM D 1129 : 2013 | Standard Terminology Relating to Water |
| ASTM D 1129 : 2013 : R2020 | Standard Terminology Relating to Water |
| ASTM D 1129 : 2006 | Standard Terminology Relating to Water |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1479 : 2016 : REDLINE | Standard Practice for Describing and Specifying Inductively Coupled Plasma Atomic Emission Spectrometers |
| ASTM D 1129 : 2013 : R2020 : EDT 1 | Standard Terminology Relating to Water |
| ASTM D 1129 : 1999 : REV A | Standard Terminology Relating to Water |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 1129 : 2006 : REV A | Standard Terminology Relating to Water |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 1129 : 2003 : REV A | Standard Terminology Relating to Water |
| ASTM D 1129 : 2002 | Standard Terminology Relating to Water |
| ASTM E 1479 : 1999 : R2011 | Standard Practice for Describing and Specifying Inductively-Coupled Plasma Atomic Emission Spectrometers |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 1129 : 2004 | Standard Terminology Relating to Water |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 1129 : 2002 : REV A | Standard Terminology Relating to Water |
| ASTM D 1129 : 2010 | Standard Terminology Relating to Water |
| ASTM D 1129 : 2006 : REV A : EDT 1 | Standard Terminology Relating to Water |
| ASTM D 1129 : 2001 | Standard Terminology Relating to Water |
| ASTM D 1129 : 2004 : EDT 1 | Standard Terminology Relating to Water |
| ASTM E 1479 : 1999 | Standard Practice for Describing and Specifying Inductively-Coupled Plasma Atomic Emission Spectrometers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.