ASTM F 439 : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
Hardcopy , PDF
12-04-2024
English
02-10-2019
Committee |
F 17
|
DocumentType |
Standard
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers chlorinated poly(vinyl chloride) (CPVC) Schedule 80 pipe fittings. Included are requirements for materials, workmanship, dimensions, and burst pressure.
Note 1:The threaded CPVC fittings covered by this specification were covered previously in Specification F437.
1.2The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 2467 : 2020 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM F 1970 : 2023 | Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems |
ASTM D 2855 : 2020 | Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets |
ASTM F 1150 : 2022 | Standard Specification for Commercial Food Waste Pulper and Waterpress Assembly |
ASTM F 493 : 2022 | Standard Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings |
ASTM F 3215 : 2022 | Standard Specification for Food Waste Dehydrators |
ASTM F 645 : 2018 : REV B | Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems |
ASTM F 437 : 2021 | Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 |
ASTM F 437 : 2015 | Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 |
ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
ASTM D 2122 : 2022 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
ASTM F 412 : 2023 | Standard Terminology Relating to Plastic Piping Systems |
ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
ASTM D 1784 : 2020 | Standard Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D 2749 : 2022 | Standard Symbols for Dimensions of Plastic Pipe Fittings |
ASTM D 2749 : 2013 | Standard Symbols for Dimensions of Plastic Pipe Fittings (Withdrawn 2022) |
ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.