ASTM F 588 : 2017 : REDLINE
Current
The latest, up-to-date edition.
Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies, Excluding Glazing Impact
English
31-10-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 04.12, 2017 Defines the ability of window assemblies of various types to restrain, delay, or frustrate forced entry.
| Committee |
E 06
|
| DocumentType |
Redline
|
| Pages |
14
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
1.1These test methods cover the ability of window assemblies of various types to restrain, delay, or frustrate forced entry.
1.2For purposes of these test methods, window assemblies are defined as described in 1.2.1 – 1.2.5 and as shown in Fig. 1. Window assemblies with a combination of operable sash and fixed panes (lites) shall be classified and tested separately for each type.
FIG. 1 Typical Window Types (viewed from the exterior)
1.2.1Type A—A window assembly which incorporates one or more sash that open by sliding, either vertically or horizontally within the plane of the wall.
1.2.2Type B—A window assembly which incorporates one or more sash that are hinged at or near two corners of the sash and that open toward the exterior (outswinging) or toward the interior (inswinging).
1.2.3Type C—A window assembly which incorporates one or more sash that are pivoted so that part of the sash opens toward the interior and part of it opens toward the exterior.
1.2.4Type D—A window assembly which incorporates one or more fixed panes (lites) or stationary sash that are designed not to open.
1.2.5Type E—A window assembly which incorporates a series of overlapping horizontal louvers that are pivoted simultaneously by a common actuator so that the bottom edge of each louver swings outward and the top edge swings inward during operation.
Note 1:See Fig. 1 for graphic depiction of window assembly types.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 2395 : 2006 | Standard Specification for Voluntary Security Performance of Window and Door Assemblies with and without Glazing Impact. |
| ASHRAE GUIDELINE 29 : 2009 | GUIDELINE FOR THE RISK MANAGEMENT OF PUBLIC HEALTH AND SAFETY IN BUILDINGS |
| CSA A440-A440.1 : 2000 | WINDOWS - USER SELECTION GUIDE TO CSA STANDARD CSA-A440-00, WINDOWS |
| ASCE 30 00 : 2000 | GUIDELINE FOR CONDITION ASSESSMENT OF THE BUILDING ENVELOPE |
| ASCE/SEI 30 14 : 2014 | GUIDELINE FOR CONDITION ASSESSMENT OF THE BUILDING ENVELOPE |
| ASTM E 2395 : 2006 : R2013 | Standard Specification for Voluntary Security Performance of Window and Door Assemblies with and without Glazing Impact |
| CSA A440 : 2017 | NORTH AMERICAN FENESTRATION STANDARD/SPECIFICATION FOR WINDOWS, DOORS, AND SKYLIGHTS |
| ASTM E 631 : 2015 : REDLINE | Standard Terminology of Building Constructions |
| ASTM E 699 : 2016 : REDLINE | Standard Specification for Agencies Involved in Testing, Quality Assurance, and Evaluating of Manufactured Building Components |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.