ASTM F 755 : 2019
Current
The latest, up-to-date edition.
Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants
Hardcopy , PDF
English
01-01-2020
Committee |
F 04
|
DocumentType |
Standard
|
Pages |
4
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification covers the properties and test methods for porous high-density-polyethylene (HDPE) and porous ultra-high-molecular-weight-polyethylene (UHMWPE) intended for use in surgical implants. The porous polyethylene may be used as a free-standing product or as a coating on a substrate in non-loaded applications.
1.2Materials covered by this standard can have a broad range of mechanical and morphological properties depending on the starting material and fabrication processes. Therefore no attempt has been made to standardize the properties, and the requirements for a specific application are not within the scope of this standard.
1.3Evaluation of the tissue response to a porous polyethylene must be completed. Guidance in establishing biocompatibility may be found in the list of references.
1.4Clinical experience and animal studies have shown that tissue will grow into the open pores of porous polyethylene. The tissue ingrowth into the pores may facilitate the establishment of implant fixation.
1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 732 : 2017 | Standard Test Method for Shear Strength of Plastics by Punch Tool |
ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
ASTM D 2238 : 2022 | Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm<sup>−1</sup> |
ASTM D 883 : 2024 : REV A | Standard Terminology Relating to Plastics |
ASTM D 1238 : 2023 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1238 : 2023 : REV A | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 732 : 2024 | Standard Test Method for Shear Strength of Plastics by Punch Tool |
ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
ASTM D 1621 : 2016 : R2023 | Standard Test Method for Compressive Properties of Rigid Cellular Plastics |
ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
ASTM D 1621 : 2016 | Standard Test Method for Compressive Properties of Rigid Cellular Plastics |
ASTM D 2238 : 1992 : R2012 : EDT 1 | Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm<sup>−1</sup> (Withdrawn 2021) |
ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
ASTM F 648 : 2014 | Standard Specification for Ultra-High-Molecular-Weight Polyethylene Powder and Fabricated Form for Surgical Implants |
ASTM F 981 : 2004 : R2016 | Standard Practice for Assessment of Compatibility of Biomaterials for Surgical Implants with Respect to Effect of Materials on Muscle and Insertion into Bone |
ASTM F 648 : 2021 | Standard Specification for Ultra-High-Molecular-Weight Polyethylene Powder and Fabricated Form for Surgical Implants |
ASTM D 1623 : 2017 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
ASTM D 1623 : 2017 : R2023 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
ASTM D 1238 : 2020 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM E 562 : 1999 | Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count |
ASTM F 981 : 2023 | Standard Practice for Assessment of Muscle and Bone Tissue Responses to Long-Term Implantable Materials Used in Medical Devices |
ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.