ASTM G 155 : 2021
Current
The latest, up-to-date edition.
Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials
Hardcopy , PDF
English
23-09-2021
Committee |
G 03
|
DocumentType |
Standard Practice
|
Pages |
12
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This practice is limited to the basic principles and procedures for operating a xenon arc lamp and water apparatus; on its own, it does not deliver a specific result.
1.2It is intended to be used in conjunction with a practice or method that defines specific exposure conditions for an application along with a means to evaluate changes in material properties. This practice is intended to reproduce the weathering effects that occur when materials are exposed to sunlight (either direct or through window glass) and moisture as humidity, rain, or dew in actual use. This practice is limited to the procedures for obtaining, measuring, and controlling conditions of exposure.
Note 1:A number of exposure procedures are listed in an appendix; however, this practice does not specify the exposure conditions best suited for the material to be tested.
Note 2:Practice G151 describes general procedures and performance requirements to be used when exposing materials in an apparatus that uses laboratory light sources.
1.3Test specimens are exposed to light from an optically-filtered xenon arc lamp under controlled environmental conditions. Different types of optical filters in combination with xenon arc light sources are described.
1.4Specimen preparation and evaluation of the results are covered in ASTM methods or specifications for specific materials. General guidance is given in Practice G151.
Note 3:General information about methods for determining the change in properties after exposure and reporting these results is described in Practice D5870.
1.5This practice is not intended for corrosion testing of bare metals.
1.6Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.7This practice is technically similar to the following ISO documents: ISO 4892-2, ISO 16474-2, ISO 105-B02, ISO 105-B04, ISO 105-B05, ISO 105-B06, and ISO 105-B10.
1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8.1Should any ozone be generated from the operation of the lamp(s), it shall be carried away from the test specimens and operating personnel by an exhaust system.
1.9This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
ASTM D 904 : 1999 : R2021 | Standard Practice for Exposure of Adhesive Specimens to Artificial Light |
ASTM G 147 : 2017 | Standard Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests |
ASTM F 852/F852M : 2020 | Standard Specification for Portable Gasoline, Kerosene, and Diesel Containers for Consumer Use |
ASTM D 7613 : 2017 : R2019 | Standard Specification for Flexible Polypropylene Reinforced (fPP-R) and Nonreinforced (fPP) Geomembranes |
ASTM D 2239 : 2021 | Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter |
ASTM F 1515 : 2021 | Standard Test Method for Measuring Light Stability of Resilient Flooring by Color Change |
ASTM G 156 : 2017 | Standard Practice for Selecting and Characterizing Weathering Reference Materials |
ASTM D 4355/D4355M : 2021 | Standard Test Method for Deterioration of Geotextiles by Exposure to Light, Moisture, and Heat in a Xenon Arc-Type Apparatus |
ASTM D 4459 : 2021 | Standard Practice for Xenon-Arc Exposure of Plastics Intended for Indoor Applications |
ASTM D 6695 : 2016 | Standard Practice for Xenon-Arc Exposures of Paint and Related Coatings |
ASTM D 2219 : 2021 | Standard Specification for Poly(Vinyl Chloride) Insulation for Wire and Cable, 60 °C Operation |
ASTM D 7942 : 2015 | Standard Specification for Thermoplastic Pavement Markings in Non Snow Plow Areas |
ASTM C 1442 : 2014 : R2021 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM D 4956 : 2019 | Standard Specification for Retroreflective Sheeting for Traffic Control |
ASTM G 178 : 2016 | Standard Practice for Determining the Activation Spectrum of a Material (Wavelength Sensitivity to an Exposure Source) Using the Sharp Cut-On Filter or Spectrographic Technique |
ASTM D 750 : 2012 : R2021 | Standard Practice for Rubber Deterioration Using Artificial Weathering Apparatus |
ASTM F 1043 : 2018 | Standard Specification for Strength and Protective Coatings on Steel Industrial Fence Framework |
ASTM F 2947/F2947M : 2021 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
ASTM D 925 : 2014 : R2019 | Standard Test Methods for Rubber Property—Staining of Surfaces (Contact, Migration, and Diffusion) |
ASTM D 7465/D7465M : 2015 : R2019 | Standard Specification for Ethylene Propylene Diene Terpolymer (EPDM) Sheet Used In Geomembrane Applications |
ASTM C 1184 : 2018 : EDT 1 | Standard Specification for Structural Silicone Sealants |
ASTM D 2220 : 2021 | Standard Specification for Poly(Vinyl Chloride) Insulation for Wire and Cable, 75 °C Operation |
ASTM F 2623 : 2019 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Systems for Non-Potable Water Applications |
ASTM D 6901 : 2015 | Standard Specification for Artists' Colored Pencils |
ASTM D 6434 : 2012 : R2018 | Standard Guide for the Selection of Test Methods for Flexible Polypropylene Geomembranes |
ASTM F 3123 : 2018 : REV A | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
ASTM C 1501 : 2019 | Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures |
ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
ASTM F 668 : 2017 | Standard Specification for Polyvinyl Chloride (PVC), Polyolefin and Other Polymer-Coated Steel Chain Link Fence Fabric |
ASTM D 3841 : 2021 | Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels |
ASTM D 8257/D8257M : 2020 | Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing |
ASTM D 5071 : 2006 : R2013 | Standard Practice for Exposure of Photodegradable Plastics in a Xenon Arc Apparatus |
ASTM D 4637/D4637M : 2015 | Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane |
ASTM E 744 : 2007 : R2015 | Standard Practice for Evaluating Solar Absorptive Materials for Thermal Applications |
ASTM D 3903 : 2015 | Standard Specification for Rubber Seals Used in Air-Heat Transport of Solar Energy Systems |
ASTM C 1519 : 2010 : R2017 | Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures |
ASTM D 1148 : 2013 : R2018 | Standard Test Method for Rubber Deterioration—Discoloration from Ultraviolet (UV) or UV/Visible Radiation and Heat Exposure of Light-Colored Surfaces |
ASTM D 4798/D4798M : 2011 : R2021 | Standard Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method) |
ASTM D 6662 : 2017 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
ASTM D 2737 : 2021 | Standard Specification for Polyethylene (PE) Plastic Tubing |
ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
ASTM D 3771 : 2015 | Standard Specification for Rubber Seals Used in Concentrating Solar Collectors |
ASTM E 2568 : 2017 : REV A | Standard Specification for PB Exterior Insulation and Finish Systems |
ASTM D 1047 : 2021 | Standard Specification for Poly(Vinyl Chloride) Jacket for Wire and Cable |
ASTM C 1523 : 2017 | Standard Test Method for Determining Modulus, Tear and Adhesion Properties of Precured Elastomeric Joint Sealants |
ASTM D 6577 : 2015 : R2019 | Standard Guide for Testing Industrial Protective Coatings |
ASTM D 4303 : 2010 : R2016 | Standard Test Methods for Lightfastness of Colorants Used in Artists' Materials |
ASTM D 4811/D4811M : 2016 | Standard Specification for Nonvulcanized (Uncured) Rubber Sheet Used as Roof Flashing |
ASTM G 141 : 2009 : R2021 | Standard Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials |
ASTM D 6878/D6878M : 2019 | Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing |
ASTM D 5329 : 2020 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements |
ASTM E 2785 : 2014 | Standard Test Method for Exposure of Firestop Materials to Severe Environmental Conditions |
ASTM C 1257 : 2015 | Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
ASTM G 151 : 2019 | Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources |
ASTM C 1900 : 2020 | Standard Practice for Weathering and Evaluation of Laminated Glass |
ASTM C 1382 : 2016 | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM C 1248 : 2018 | Standard Test Method for Staining of Porous Substrate by Joint Sealants |
ASTM C 1483/C1483M : 2017 | Standard Specification for Exterior Solar Radiation Control Coatings on Buildings |
ASTM D 7869 : 2017 | Standard Practice for Xenon Arc Exposure Test with Enhanced Light and Water Exposure for Transportation Coatings |
ASTM D 2513 : 2020 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
ASTM E 3119 : 2019 | Standard Test Method for Accelerated Aging of Environmentally Controlled Dynamic Glazing |
ASTM D 2565 : 2016 | Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications |
ASTM D 3667 : 2016 | Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors |
ASTM E 2136 : 2004 : R2013 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Durability (Withdrawn 2022) |
ASTM D 6754/D6754M : 2015 | Standard Specification for Ketone Ethylene Ester Based Sheet Roofing |
ASTM C 1530/C1530M : 2004 : R2019 | Standard Specification for Non-Asbestos Fiber-Cement Roofing Shakes, Shingles, and Slates with Designed Varying Profiles and Thicknesses |
ASTM D 6551/D6551M : 2005 : R2019 | Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Xenon-Arc Exposure Apparatus |
ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
ASTM D 4434/D4434M : 2021 | Standard Specification for Poly(Vinyl Chloride) Sheet Roofing |
ASTM F 668 : 2017 : R2022 | Standard Specification for Polyvinyl Chloride (PVC), Polyolefin and Other Polymer-Coated Steel Chain Link Fence Fabric |
ASTM F 1043 : 2018 : R2022 | Standard Specification for Strength and Protective Coatings on Steel Industrial Fence Framework |
ASTM D 5071 : 2006 : R2021 | Standard Practice for Exposure of Photodegradable Plastics in a Xenon Arc Apparatus |
ASTM D 3903 : 2015 : R2022 | Standard Specification for Rubber Seals Used in Air-Heat Transport of Solar Energy Systems |
ASTM G 178 : 2016 : R2023 | Standard Practice for Determining the Activation Spectrum of a Material (Wavelength Sensitivity to an Exposure Source) Using the Sharp Cut-On Filter or Spectrographic Technique |
ASTM F 852/F852M : 2022 | Standard Specification for Portable Gasoline, Kerosene, and Diesel Containers for Consumer Use |
ASTM D 7613 : 2017 : R2023 | Standard Specification for Flexible Polypropylene Reinforced (fPP-R) and Nonreinforced (fPP) Geomembranes |
ASTM F 2623 : 2022 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Systems for Non-Potable Water Applications |
ASTM E 2785 : 2014 : R2022 | Standard Test Method for Exposure of Firestop Materials to Severe Environmental Conditions |
ASTM C 1248 : 2022 | Standard Test Method for Staining of Porous Substrate by Joint Sealants |
ASTM D 3771 : 2015 : R2022 | Standard Specification for Rubber Seals Used in Concentrating Solar Collectors |
ASTM D 6662 : 2022 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
ASTM C 1519 : 2010 : R2022 | Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures |
ASTM F 2947/F2947M : 2021 : REV A | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
ASTM C 1483/C1483M : 2017 : R2022 | Standard Specification for Exterior Solar Radiation Control Coatings on Buildings |
ASTM C 1184 : 2023 | Standard Specification for Structural Silicone Sealants |
ASTM F 3123 : 2022 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
ASTM C 1382 : 2016 : R2023 | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM D 4303 : 2010 : R2022 | Standard Test Methods for Lightfastness of Colorants Used in Artists' Materials |
ASTM C 1257 : 2015 : R2023 | Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
ASTM D 7942 : 2015 : R2023 | Standard Specification for Thermoplastic Pavement Markings in Non Snow Plow Areas |
ASTM C 1501 : 2023 | Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures |
ASTM D 2737 : 2022 | Standard Specification for Polyethylene (PE) Plastic Tubing |
ASTM D 3794 : 2022 | Standard Guide for Testing Coil Coatings |
ASTM D 6901 : 2015 : R2021 | Standard Specification for Artists' Colored Pencils |
ASTM D 6754/D6754M : 2015 : R2022 | Standard Specification for Ketone Ethylene Ester Based Sheet Roofing |
ASTM D 6878/D6878M : 2021 | Standard Specification for Thermoplastic Polyolefin-Based Sheet Roofing |
ASTM D 4637/D4637M : 2015 : R2021 : EDT 1 | Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane |
ASTM D 7465/D7465M : 2015 : R2023 | Standard Specification for Ethylene Propylene Diene Terpolymer (EPDM) Sheet Used In Geomembrane Applications |
ASTM E 2141 : 2021 | Standard Test Method for Accelerated Aging of Electrochromic Devices in Sealed Insulating Glass Units |
ASTM D 2239 : 2022 | Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter |
ASTM D 8514/D8514M : 2023 | Standard Specification for Flexible, Retroreflective Sheeting for Use in High Visibility Vehicle Markings |
ASTM D 4811/D4811M : 2016 : R2023 | Standard Specification for Nonvulcanized (Uncured) Rubber Sheet Used as Roof Flashing |
ASTM D 8257/D8257M : 2022 | Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing |
ASTM C 1916 : 2021 | Standard Specification for Flexible Protective Jackets Made of Modified Asphalt/Butyl Rubber for Use over Thermal Insulation |
ASTM D 3667 : 2016 : R2022 | Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors |
ASTM E 744 : 2007 : R2022 | Standard Practice for Evaluating Solar Absorptive Materials for Thermal Applications |
ASTM G 160 : 2012 : R2019 | Standard Practice for Evaluating Microbial Susceptibility of Nonmetallic Materials By Laboratory Soil Burial |
ASTM G 113 : 2024 | Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials |
ASTM D 2565 : 2023 | Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications |
ASTM G 153 : 2013 : R2021 | Standard Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
ASTM D 5870 : 2022 | Standard Practice for Calculating Property Retention Index of Plastics |
ASTM G 113 : 2016 | Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials |
ASTM D 6695 : 2024 | Standard Practice for Xenon-Arc Exposures of Paint and Related Coatings |
ASTM G 113 : 2022 | Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials |
ASTM D 5870 : 2016 | Standard Practice for Calculating Property Retention Index of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.