AWWA C207 : 2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
STEEL PIPE FLANGES FOR WATERWORKS SERVICE, SIZES 4 IN. THROUGH 144 IN. (100 MM THROUGH 3,600 MM)
Available format(s)
Hardcopy , PDF
Superseded date
11-02-2019
Superseded by
Language(s)
English
Published date
01-01-2013
Publisher
Foreword
I Introduction
II Special Issues
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Delivery
Appendixes
A - Bibliography
B - Steel-Hub Flanges
Specifies ring-type slip-on flanges and blind flanges.
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM F 1311 : 1990 : R2012 | Standard Specification for Large–Diameter Fabricated Carbon Steel Flanges |
| BS EN 593:2017 | Industrial valves. Metallic butterfly valves for general purposes |
| AWWA M55 : 1 | PE PIPE - DESIGN AND INSTALLATION |
| ASTM F 2880 : 2014 : REDLINE | Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3/4</den></fraction > in. to 65 in. |
| AWWA C712 : 2015 | COLD-WATER METERS - SINGLEJET TYPE |
| ASTM F 1311 : 1990 : R2006 | Standard Specification for Large-Diameter Fabricated Carbon Steel Flanges |
| AWWA C751 : 2016 | MAGNETIC INDUCTIVE FLOWMETERS |
| I.S. EN 593:2017 | INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| AWWA C604:2017 | INSTALLATION OF BURIED STEEL WATER PIPE - 4 IN. (100 MM) AND LARGER |
| AWWA C515 : 2015 | REDUCED-WALL, RESILIENT-SEATED GATE VALVES FOR WATER SUPPLY SERVICE |
| AWWA C111/A21.11 : 2017 | RUBBER-GASKET JOINTS FOR DUCTILE-IRON PRESSURE PIPE AND FITTINGS |
| ANSI/AWWA C514 : 2015 | AIR VALVE AND VENT INFLOW PREVENTER ASSEMBLIES FOR POTABLE WATER DISTRIBUTION SYSTEM AND STORAGE FACILITIES |
| AWWA E103 : 2015 | HORIZONTAL AND VERTICAL LINE-SHAFT PUMPS |
| AWWA C701 : 2015 | COLD-WATER METERS - TURBINE TYPE, FOR CUSTOMER SERVICE |
| AWWA C703 : 2015 | COLD-WATER METERS - FIRE-SERVICE TYPE |
| AWWA C516 : 2014 | LARGE-DIAMETER RUBBER-SEATED BUTTERFLY VALVES, SIZES 78 IN. (2,000 MM) AND LARGER |
| ASME B31.1 : 2016 | POWER PIPING |
| ASME B31.3:2016 | PROCESS PIPING |
| ANSI/AWWA C702 : 2015 | COLD-WATER METERS - COMPOUND TYPE |
| AWWA C704 : 2015 | PROPELLER-TYPE METERS FOR WATERWORKS APPLICATIONS |
| AWWA C520 : 2014 | KNIFE GATE VALVES, SIZES 2 IN. (50 MM) THROUGH 96 IN. (2,400 MM) |
| AWWA C712 : 2019 | COLD-WATER METERS - SINGLEJET TYPE |
| ANSI/AWWA C115/A21.15 : 2011 | FLANGED DUCTILE-IRON PIPE WITH DUCTILE-IRON OR GRAY-IRON THREADED FLANGES |
| ASTM F 1311 : 1990 : R2001 | Standard Specification for Large-Diameter Fabricated Carbon Steel Flanges |
| ANSI/AWWA D120 : 2009 | THERMOSETTING FIBERGLASS-REINFORCED PLASTIC TANKS |
| AWWA C509 : 2015 | RESILIENT-SEATED GATE VALVES FOR WATER SUPPLY SERVICE |
| AWWA C702 : 2019 | COLD-WATER METERS - COMPOUND TYPE |
| EN 593:2017 | Industrial valves - Metallic butterfly valves for general purposes |
| MSS SP 67 : 2017 | BUTTERFLY VALVES |
| ASTM F 1311 : 1990 : R1995 : EDT 1 | Standard Specification for Large-Diameter Fabricated Carbon Steel Flanges |
| ASTM F 1311 : 1990 : R2018 | Standard Specification for Large–Diameter Fabricated Carbon Steel Flanges |
| AWWA C223 : 2013 | FABRICATED STEEL AND STAINLESS STEEL-TAPPING SLEEVES |
| AWWA C153/A21.53 : 2011 | DUCTILE-IRON COMPACT FITTINGS |
| ASME B16.10 : 2017 | FACE-TO-FACE AND END-TO-END DIMENSIONS OF VALVES |
| PIP PNSM0116 : 2013 | PURCHASING REQUIREMENTS FOR FITTINGS AND FLANGES |
| ASME B31.3 SPANISH : 2010 | PROCESS PIPING |
| ASME B18.2.1 : 2012 | SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES) |
| AWWA C222 : 2008 | POLYURETHANE COATINGS AND LININGS FOR STEEL WATER PIPE AND FITTINGS |
| AWWA C209 : 2013 | COLD-APPLIED TAPE COATINGS FOR STEEL WATER PIPE, SPECIAL SECTIONS, CONNECTIONS, AND FITTINGS |
| ANSI/AWWA C216 : 2015 | HEAT-SHRINKABLE CROSS-LINKED POLYOLEFIN COATINGS FOR STEEL WATER PIPE AND FITTINGS |
| ASTM A 181/A181M : 2014 : REDLINE | Standard Specification for Carbon Steel Forgings, for General-Purpose Piping |
| ANSI/AWWA C200 : 2017 | STEEL WATER PIPE, 6 IN. (150 MM) AND LARGER |
| AWWA C208 : 2012 | DIMENSIONS FOR FABRICATED STEEL WATER PIPE FITTINGS |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| ANSI/AWWA C213 : 2015 | FUSION-BONDED EPOXY COATINGS AND LININGS FOR STEEL WATER PIPE AND FITTINGS |
| AWWA M11 : 2004 | STEEL PIPE: A GUIDE FOR DESIGN AND INSTALLATION |
| ASME B16.1 : 2015 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
| ASTM A 563 : 2015 : REDLINE | Standard Specification for Carbon and Alloy Steel Nuts |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| AWWA C203 : 2015 | COAL-TAR PROTECTIVE COATINGS AND LININGS FOR STEEL WATER PIPE |
| AWS D1.1/D1.1M : 2015 | STRUCTURAL WELDING CODE-STEEL |
| ASME B16.47 : 2017 | LARGE DIAMETER STEEL FLANGES: NPS 26 THROUGH NPS 60 METRIC/INCH STANDARD |
| AWWA C217 : 2016 | MICROCRYSTALLINE WAX AND PETROLATUM TAPE COATING SYSTEMS FOR STEEL WATER PIPE AND FITTINGS |
| AWWA C218 : 2016 | LIQUID COATINGS FOR ABOVEGROUND STEEL WATER PIPE AND FITTINGS |
| AWWA C210 : 2015 | LIQUID-EPOXY COATINGS AND LININGS FOR STEEL WATER PIPE AND FITTINGS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.