AWWA C905 : 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
POLYVINYL CHLORIDE (PVC) PRESSURE PIPE AND FABRICATED FITTINGS, 14 IN. THROUGH 48 IN. (350 MM THROUGH 1,200 MM), FOR WATER TRANSMISSION AND DISTRIBUTION
Hardcopy , PDF
01-08-2016
English
01-01-2010
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
I Introduction
II Special Issues
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Delivery
Appendixes
A - Bibliography
B - Recurring (Cyclic) Surge - Figures and Design Example
Covers eight dimension ratio (DRs) and nominal pipe sizes ranging from 14 in. through 48 in. (350 mm through 1,200 mm).
| DocumentType |
Standard
|
| Pages |
40
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASCE/EWRI 12-13, 13-13, 14-13 : 2013 | STANDARD GUIDELINES FOR THE DESIGN, INSTALLATION, AND OPERATION AND MAINTENANCE OF URBAN SUBSURFACE DRAINAGE |
| ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
| ICC IRC CODE AND COMMENTARY VOLUME 2 : 2015 | IRC® Code and Commentary, Volume 2 |
| AWWA C605 : 2013 | UNDERGROUND INSTALLATION OF POLYVINYL CHLORIDE (PVC) AND MOLECULARLY ORIENTED POLYVINYL CHLORIDE (PVCO) PRESSURE PIPE AND FITTINGS |
| AWWA M23 : 2 | PVC PIPE - DESIGN AND INSTALLATION |
| AWWA M28 : 2014 | REHABILITATION OF WATER MAINS |
| NSF 61 : 2016 | DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS |
| AWWA M23 : 2 | PVC PIPE - DESIGN AND INSTALLATION |
| PPI TR 3 : 2017 | POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE |
| ASTM F 477 : 2014 : REDLINE | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM D 2855 : 2015 : REDLINE | Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets |
| AWWA C907 : 2017 | INJECTION-MOLDED POLYVINYL CHLORIDE (PVC) PRESSURE FITTINGS, 4 IN. THROUGH 12 IN. (100 MM THROUGH 300 MM), FOR WATER, WASTEWATER, AND RECLAIMED WATER SERVICE |
| ASTM D 2241 : 2015 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
| AWWA C605 : 2013 | UNDERGROUND INSTALLATION OF POLYVINYL CHLORIDE (PVC) AND MOLECULARLY ORIENTED POLYVINYL CHLORIDE (PVCO) PRESSURE PIPE AND FITTINGS |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2290 : 2016-12 | TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE |
| AWWA C900 : 2016 | POLYVINYL CHLORIDE (PVC) PRESSURE PIPE AND FABRICATED FITTINGS, 4 IN. THROUGH 60 IN. (100 MM THROUGH 1,500 MM) |
| ASTM D 1784 : 2011 : REDLINE | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.