BS 1722-2:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fences Specification for strained wire and wire mesh netting fences
Hardcopy , PDF
27-10-2020
English
31-08-2010
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Materials for general pattern strained wire fences
5 Installation of general pattern strained wire fences
6 Materials for dropper pattern fences
7 Installation of dropper pattern fences
8 Materials for general pattern wire mesh fences
9 Installation of general pattern wire mesh fences
10 Materials for spring steel and high tensile mesh
fences
11 Installation of spring steel and high tensile mesh
fences
12 Statement of conformity
Annexes
Annex A (normative) - Concrete components
Annex B (normative) - Steel components and protective
treatment
Annex C (informative) - Specifying a strained wire fence
Annex D (normative) - Method of measuring line wire tension
Annex E (informative) - Determination of moisture content
Bibliography
Describes requirements for the construction and installation of general pattern and dropper pattern strained wire fences and rectangular wire mesh fences, including mild steel or high tensile woven wire fencing, welded mesh fencing, hexagonal wire netting fences of the general pattern, and spring steel wire pattern fences where the mesh is fixed onto spring steel line wires.
Committee |
B/201
|
DevelopmentNote |
Supersedes BS 1722-2(2000) and 06/30139497 DC (11/2006) Reviewed and confirmed by BSI, December 2011. (11/2011)
|
DocumentType |
Standard
|
Pages |
54
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
This part of BS1722 specifies requirements for the construction and installation of general pattern and dropper pattern strained wire fences and rectangular wire mesh fences, including mild steel or high tensile woven wire fencing, welded mesh fencing, hexagonal wire netting fences of the general pattern, and spring steel wire pattern fences where the mesh is fixed onto spring steel line wires.
This standard includes requirements for protective treatments. However, maintenance requirements of the fence after installation are outside the scope of this standard.
NOTE Figure1 illustrates the general characteristics of strained wire fences. It is not intended to illustrate any particular requirements of this standard but provides guidance as to the general layout of a typical fence, and on the terminology associated with this form of fencing.
S.R. CWA 16221:2010 | VEHICLE SECURITY BARRIERS - PERFORMANCE REQUIREMENTS, TEST METHODS AND GUIDANCE ON APPLICATION |
BS EN 12878:2014 | Pigments for the colouring of building materials based on cement and/or lime. Specifications and methods of test |
BS EN 10219-1:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels Technical delivery requirements |
BS 4483:2005 | Steel fabric for the reinforcement of concrete. Specification |
BS EN 287-1:2011 | Qualification test of welders. Fusion welding Steels |
BS EN 12839:2012 | Precast concrete products. Elements for fences |
BS EN 10056-1:2017 | Structural steel equal and unequal leg angles Dimensions |
BS 8500-2:2002 | Concrete. Complementary British Standard to BS EN 206-1 Specification for constituent materials and concrete |
BS EN 10296-1:2003 | Welded circular steel tubes for mechanical and general engineering purposes. Technical delivery conditions Non-alloy and alloy steel tubes |
BS EN 10025-2:2004 | Hot rolled products of structural steels Technical delivery conditions for non-alloy structural steels |
BS EN 206-1:2000 | Concrete Specification, performance, production and conformity |
BS EN 10223-2:2012 | Steel wire and wire products for fencing and netting Hexagonal steel wire netting for agricultural, insulation and fencing purposes |
BS EN 212:2003 | Wood preservatives. General guidance on sampling and preparation for analysis of wood preservatives and treated timber |
BS EN 12620:2013 | Aggregates for concrete |
BS 4449(2005) : 2005 | STEEL FOR THE REINFORCEMENT OF CONCRETE - WELDABLE REINFORCING STEEL - BAR, COIL AND DECOILED PRODUCT - SPECIFICATION |
BS EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels Technical delivery requirements |
BS EN 844-9:1997 | Round and sawn timber. Terminology Terms relating to features of sawn timber |
BS EN 10244-2:2009 | Steel wire and wire products. Non-ferrous metallic coatings on steel wire Zinc or zinc alloy coatings |
BS EN 197-1:2011 | Cement Composition, specifications and conformity criteria for common cements |
BS EN 10223-5:2012 | Steel wire and wire products for fencing and netting Steel wire woven hinged joint and knotted mesh fencing |
BS EN 10240:1998 | Internal and/or external protective coatings for steel tubes. Specification for hot dip galvanized coatings applied in automatic plants |
BS 1722-4:1986 | Fences Specification for cleft chestnut pale fences |
BS 3892:1965 | Pulverized fuel ash for concrete |
BS EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods |
BS 8500-1:2002 | Concrete. Complementary British Standard to BS EN 206-1 Method of specifying and guidance for the specifier |
BS EN 1011-2:2001 | Welding. Recommendations for welding of metallic materials Arc welding of ferritic steels |
BS EN 10219-2:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels Tolerances, dimensions and sectional properties |
BS EN 10210-2:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels Tolerances, dimensions and sectional properties |
BS EN 10255:2004 | Non-alloy steel tubes suitable for welding and threading. Technical delivery conditions |
BS 4027:1996 | Specification for sulfate-resisting Portland cement |
BS 4320:1968 | Specification for metal washers for general engineering purposes. Metric series |
BS EN 10223-1:2012 | Steel wire and wire products for fencing and netting Zinc and zinc-alloy coated steel barbed wire |
BS EN 1011-1:2009 | Welding. Recommendations for welding of metallic materials General guidance for arc welding |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.