BS 4500-1.2(1990) : AMD 7631
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ISO LIMITS AND FITS - GENERAL, TOLERANCES AND DEVIATIONS - TABLES OF COMMONLY USED TOLERANCE GRADES AND LIMIT DEVIATIONS FOR HOLES AND SHAFTS
Superseded date
15-08-1993
Superseded by
Published date
23-11-2012
Publisher
Sorry this product is not available in your region.
Establishes values of the limit deviations for commonly used tolerance classes for holes and shafts calculated from the information given in ISO 286-1. Covers values for the upper deviations ES and es and the lower deviations EI and ei. Includes several tables and figures. BS AMD 7631 RENUMBERS THIS STANDARD TO BS EN 20286-2
| Committee |
GME/5
|
| DevelopmentNote |
Superseded and renumbered by BS EN 20286-2 (07/2004)
|
| DocumentType |
Standard
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 286-2:2010 | Identical |
| BS 328-6:1992 | Drills and reamers Countersinks, 90°, with parallel shanks and solid pilots |
| BS 3884-2:1990 | Modular units for machine tools Specification for workholding pallets up to 800 mm nominal size |
| BS 1919-1:1993 | Hacksaw blades Specification for hand and machine hacksaw blades |
| BS 341-1:1991 | Transportable gas container valves Specification for industrial valves for working pressures up to and including 300 bar |
| BS 7724:1994 | Specification for split pins (metric series) |
| BS AU 249:1993 | Specification for clutch housings for reciprocating internal combustion engines. Nominal dimensions and tolerances |
| BS 4377:1991 | Specification for tapping of holes to receive wire thread inserts (ISO metric threads) |
| BS 328-1:1993 | Drills and reamers Specification for twist drills |
| BS 949-3:1993 | Screwing taps. Specification for pipe thread taps |
| BS 4480-1:1992 | Plain bearings: metric series Sintered bushes. Dimensions and tolerances |
| BS 7296-1:1990 | Cavities for hydraulic fluid power cartridge valves Specification for two-port slip-in valves |
| BS 3884-3:1990 | Modular units for machine tools Specification for workholding pallets over 800 mm nominal size |
| BS QC 030000:1993 | Harmonized system of quality assessment for electronic components. Rectangular connectors for frequencies below 3 MHz. Generic specification. General requirements and guide for the preparation of detail specifications for connectors with assessed quality |
| BS 1574:1994 | Specification for split pins (inch series) |
| BS 5594:1993 | Specification for leaf chains, clevises and sheaves |
| BS 328-7:1992 | Drills and reamers Counterbores with parallel shanks and solid pilots |
| BS 7637:1993 | Specification for linear motion, recirculating ball, sleeve type rolling bearings (metric series) |
| BS 7586:1992 | Specification for combination wrenches |
| BS 1759:1969 | Specification for knurling wheels |
| BS EN 20898-2:1994 | Mechanical properties of fasteners Nuts with specified proof load values. Coarse thread |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| BS 328-8:1992 | Drills and reamers Spot drills |
| BS 5341-6.1:1992 | Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Vocabulary, inspection methods and generic specifications Vocabulary |
| ISO 8015:2011 | Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules |
| ISO 5166:1982 | System of cone fits for cones from C = 1 : 3 to 1 : 500, lengths from 6 to 630 mm and diameters up to 500 mm |
| ISO 2692:2014 | Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 406:1987 | Technical drawings Tolerancing of linear and angular dimensions |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| ISO/R 1938:1971 | ISO system of limits and fits Part II : Inspection of plain workpieces |
| ISO 8062:1994 | Castings System of dimensional tolerances and machining allowances |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.