Skip to content
Please enter a keyword to search

  • BS 6744(2001) : 2001

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    STAINLESS STEEL BARS FOR THE REINFORCEMENT OF AND USE IN CONCRETE - REQUIREMENTS AND TEST METHODS

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-05-2016

    Language(s):  English

    Published date:  01-01-2001

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms, definitions and symbols
    4 Designation
    5 Standard sizes
    6 Dimensions, mass and tolerances
    7 Steelmaking process
    8 Chemical composition
    9 Surface quality
    10 Surface geometry
    11 Conditions of supply
    12 Mechanical and physical properties
    13 Retests
    14 Product identification
    Annex A (normative) - Determination of the effective
            cross-sectional area and mass per metre run of
            ribbed bars
    Annex B (informative) - Guidance on grade selection to prevent
            corrosion
    Annex C (normative) - Measurement of the geometrical
            characteristics
    Annex D (normative) - Inspection and testing
    Annex E (normative) - Bend test
    Annex F (normative) - Method of test for fatigue properties
            of ribbed bars
    Annex G (informative) - Comparison of similar specifications
    Annex H (informative) - Guidance on magnetic properties
    Annex I (informative) - Third party certification
    Annex J (informative) - Guidance on coefficients of thermal
            expansion
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines requirements and explains methods of test for solid stainless steel bars used for the reinforcement of, and use in, concrete. It also covers plain round steel bars in grade 200 and ribbed and plain steel bars in grades 500 and 650.

    General Product Information - (Show below) - (Hide below)

    Committee ISE/9/1
    Development Note Supersedes BS 6744(1986) and 00/709560 DC. (08/2001) 2001 Edition Re-Issued in March 2009 & incorporates AMD 2 2009. Supersedes 07/30168128 DC. (03/2009)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 5642-1(1978) : 1978 SILLS, COPINGS AND CAPPINGS - PART 1: SPECIFICATION FOR WINDOW SILLS OF PRECAST CONCRETE, CAST STONE, CLAYWARE, SLATE AND NATURAL STONE
    BS 5642-2(1983) : 1983 SILLS, COPINGS AND CAPPINGS - PART 2: SPECIFICATION FOR COPINGS AND CAPPINGS OF PRECAST CONCRETE, CAST STONE, CLAYWARE, SLATE AND NATURAL STONE
    ACI 376 : 2011 CODE REQUIREMENTS FOR DESIGN AND CONSTRUCTION OF CONCRETE STRUCTURES FOR THE CONTAINMENT OF REFRIGERATED LIQUEFIED GASES AND COMMENTARY
    ACI 376M : 2011 CODE REQUIREMENTS FOR DESIGN AND CONSTRUCTION OF CONCRETE STRUCTURES FOR THE CONTAINMENT OF REFRIGERATED LIQUEFIED GASES (METRIC)
    EEMUA 207 : 2009 DOUBLE CONCRETE TANKS FOR LIQUEFIED GAS - GUIDE TO DESIGN, CONSTRUCTION AND OPERATION
    BS 5628-2:2005 CODE OF PRACTICE FOR THE USE OF MASONRY - PART 2: STRUCTURAL USE OF REINFORCED AND PRESTRESSED MASONRY
    IEC TS 62600-2:2016 Marine energy - Wave, tidal and other water current converters - Part 2: Design requirements for marine energy systems
    BS 8666:2005 Scheduling, dimensioning, bending and cutting of steel reinforcement for concrete. Specification
    ISO 17660-1:2006 Welding — Welding of reinforcing steel — Part 1: Load-bearing welded joints
    BS EN ISO 17660-1:2006 Welding. Welding of reinforcing steel Load-bearing welded joints
    ISO 17660-2:2006 Welding — Welding of reinforcing steel — Part 2: Non load-bearing welded joints
    BS 8415(2005) : 2005 MONUMENTS WITHIN BURIAL GROUNDS AND MEMORIAL SITES - SPECIFICATION
    BS 8081:1989 Code of practice for ground anchorages
    EN ISO 17660-2:2006 Welding - Welding of reinforcing steel - Part 2: Non load-bearing welded joints (ISO 17660-2:2006)
    BS 6349-1-4:2013 Maritime works General. Code of practice for materials
    BS 8597:2015 Steels for the reinforcement of concrete. Reinforcement couplers. Requirements and test methods
    BS EN ISO 17660-2:2006 Welding. Welding of reinforcing steel Non load-bearing welded joints
    EN ISO 17660-1:2006 Welding - Welding of reinforcing steel - Part 1: Load-bearing welded joints (ISO 17660-1:2006)
    BS 8007:1987 CODE OF PRACTICE FOR DESIGN OF CONCRETE STRUCTURES FOR RETAINING AQUEOUS LIQUIDS

    Standards Referencing This Book - (Show below) - (Hide below)

    BS EN 10088-1:2014 Stainless steels List of stainless steels
    BS EN 10021:2006 General technical delivery conditions for steel products
    BS EN 10088-3:2014 Stainless steels Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
    BS EN 10221:1996 Specification for surface quality classes for hot-rolled bars and rods. Technical delivery conditions
    BS 4449(2005) : 2005 STEEL FOR THE REINFORCEMENT OF CONCRETE - WELDABLE REINFORCING STEEL - BAR, COIL AND DECOILED PRODUCT - SPECIFICATION
    BS EN ISO 3651-2:1998 Determination of resistance to intergranular corrosion of stainless steels Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels. Corrosion test in media containing sulfuric acid
    ISO 10606:1995 Steel for the reinforcement of concrete Determination of percentage total elongation at maximum force
    BS 8666:2005 Scheduling, dimensioning, bending and cutting of steel reinforcement for concrete. Specification
    BS EN 10045-1:1990 Charpy impact test on metallic materials Test method (V- and U-notches)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective