BS 7158:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics inspection chambers for drains and sewers. Specification
Hardcopy , PDF
18-12-2003
English
15-08-2001
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Committees responsible
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
5 Dimensions
6 Appearance
7 Performance requirements
8 Marking
Annex A (normative) Methods of test for watertightness
Annex B (normative) Method of test for resistance to
angular deflection
Annex C (normative) Method of test for resistance to
diametric distortion of chamber joint assemblies
with flexible pipe system
Annex D (normative) Method of test for shear resistance of
chamber joint assemblies with rigid pipe system
Annex E (normative) Method of test for resistance to
elevated temperature cycling
Annex F (normative) Method of test for the determination
of specific tangential initial stiffness
Annex G (normative) Method of test for resistance to
vertical loading
Annex H (informative) Guidance on use of inspection chambers
relative to surface load and installation procedures
Annex I (normative) Method of test for resistance to
negative pressure
Annex J (informative) Guidance on quality control testing
Bibliography
Specifies requirements for plastics inspection chambers for use at depths to invert not exceeding 6 m in the construction of drainage and sewerage systems. It is applicable to non-man-entry chambers with or without raising pieces and having a nominal cross-section.
| Committee |
PRI/88
|
| DevelopmentNote |
Supersedes BS 7158(1989) (07/2001) Supersedes 99/121878 DC. (01/2004) Reviewed and confirmed by BSI, June 2007. (05/2007)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| BS EN 1610:2015 | Construction and testing of drains and sewers |
| PREN 13598-1 : DRAFT 2010 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| BS EN 752-7:1998 | Drain and sewer systems outside buildings Maintenance and operations |
| BS 7903:1997 | Guide to selection and use of gully tops and manhole covers for installation within the highway |
| BS EN 752-6:1998 | Drain and sewer systems outside buildings Pumping installations |
| BS 3496:1989 | Specification for E glass fibre chopped strand mat for reinforcement of polyester and other liquid laminating systems |
| BS EN 752-2:1997 | Drain and sewer systems outside buildings Performance requirements |
| BS EN 1295-1 : 1998 | STRUCTURAL DESIGN OF BURIED PIPELINES UNDER VARIOUS CONDITIONS OF LOADING - PART 1: GENERAL REQUIREMENTS |
| BS EN 681-1:1996 | Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Vulcanized rubber |
| BS 6209:1982 | Specification for solvent cement for non-pressure thermoplastics pipe systems |
| BS EN 295-1:2013 | Vitrified clay pipe systems for drains and sewers Requirements for pipes, fittings and joints |
| BS EN 681-3:2000 | Elastomeric seals. Materials requirements for pipe joint seals used in water and drainage applications Cellular materials of vulcanized rubber |
| BS 5955-6:1980 | Plastics pipework (thermoplastics materials) Code of practice for the installation of unplasticized PVC pipework for gravity drains and sewers |
| BS EN 752-5:1998 | Drain and sewer systems outside buildings Rehabilitation |
| BS 2782-11.1103V(1995) : 1995 | METHODS OF TESTING PLASTICS - THERMOPLASTICS PIPES, FITTINGS AND VALVES - PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS PIPES AND FITTINGS - DETERMINATION OF VICAT SOFTENING TEMPERATURE |
| DIN 1259-1:2001-09 | GLASS - PART 1: TERMINOLOGY FOR GLASS TYPES AND GROUPS |
| BS 8301:1985 | Code of practice for building drainage |
| BS 4346-1:1969 | Joints and fittings for use with unplasticized PVC pressure pipes Injection moulded unplasticized PVC fittings for solvent welding for use with pressure pipes, including potable water supply |
| BS EN 681-2:2000 | Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Thermoplastic elastomers |
| BS EN 752-4:1998 | Drain and sewer systems outside buildings Hydraulic design and environmental considerations |
| ISO 2078:1993 | Textile glass Yarns Designation |
| BS EN 45011:1998 | General requirements for bodies operating product certification systems |
| BS ISO 472:1988 | Plastics. Vocabulary |
| BS EN 752-3:1997 | Drain and sewer systems outside buildings Planning |
| BS 3447:1962 | Glossary of terms used in the glass industry |
| BS EN 124:1994 | Gully tops and manhole tops for vehicular and pedestrian areas. Design requirements, type testing, marking, quality control |
| BS EN 681-4:2000 | Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Cast polyurethane sealing elements |
| BS EN 1401-1:2009 | Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for pipes, fittings and the system |
| BS EN 752-1:1996 | Drain and sewer systems outside buildings Generalities and definitions |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.