BS 7910:2005
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
Guide to methods for assessing the acceptability of flaws in metallic structures
Hardcopy , PDF
30-11-2018
English
28-09-2007
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Committees responsible
Foreword
Introduction
1 Scope
2 Normative references
3 Symbols and definitions
4 Types of flaw
5 Modes of failure and material damage mechanisms
6 Information required for assessment
7 Assessment for fracture resistance
8 Assessment for fatigue
9 Assessment of flaws under creep conditions
10 Assessment for other modes of failure
Annex A (normative) Evaluation under combined direct and
shear stresses or mode I, II and III
loads
Annex B (informative) Assessment procedures for tubular
joints in offshore structures
Annex C (informative) Fracture assessment procedures for
pressure vessels and pipelines
Annex D (normative) Stress due to misalignment
Annex E (normative) Flaw recharacterization
Annex F (informative) A procedure for leak-before-break
assessment
Annex G (normative) The assessment of corrosion in pipes
and pressure vessels
Annex H (normative) Reporting of fracture, fatigue or creep
assessments
Annex I (informative) The significance of weld strength mismatch
on the fracture behaviour of welded joints
Annex J (informative) Use of Charpy V-notch impact tests to
estimate fracture toughness
Annex K (normative) Reliability, partial safety factors, number
of tests and reserve factor
Annex L (normative) Fracture toughness determination for welds
Annex M (normative) Stress intensity factor solutions
Annex N (normative) Simplified procedures for determining the
acceptability of a known flaw or
estimating the acceptable flaw size using
Level 1 fracture procedures
Annex O (informative) Consideration of proof testing and warm
prestressing
Annex P (normative) Calculation of reference stress
Annex Q (informative) Residual stress distributions in as-welded
joints
Annex R (normative) Determination of plasticity interaction
effects with combined primary and secondary
loading
Annex S (normative) Approximate numerical integration methods for
fatigue life estimation
Annex T (informative) Information for making high temperature crack
growth assessments
Annex U (informative) Worked example to demonstrate high temperature
failure assessment procedure
Bibliography
Define methods for assessing the acceptability of flaws in all types of structures and components.
| Committee |
WEE/37
|
| DevelopmentNote |
Supersedes BS 7910(1999) and 04/30111613 DC (08/2005) Supersedes 07/30164727 DC. (10/2007)
|
| DocumentType |
Standard
|
| Pages |
306
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| DD ENV 1999-1.2 : DRAFT DEC 2000 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-2: GENERAL RULES - STRUCTURAL FIRE DESIGN |
| ASME PV CODE 3 NF DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - SUPPORTS |
| BS 7608:1993 | Code of practice for fatigue design and assessment of steel structures |
| BS EN 1291:1998 | Non-destructive testing of welds. Magnetic particle testing of welds. Acceptance levels |
| BS EN 12517:1998 | Non-destructive testing of welds. Radiographic testing of welded joints. Acceptance levels |
| ASME PV CODE 3 ND DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - CLASS 3 COMPONENTS |
| BS EN ISO 12737:2010 | Metallic materials. Determination of plane-strain fracture toughness |
| ASME PV CODE 3 NH DIV 1 : 2015 | BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - CLASS 1 COMPONENTS IN ELEVATED TEMPERATURE SERVICE |
| ASME PV CODE 3 NCA DIV 1&2 : 2017 | BPVC Section III-Rules for Constructions of Nuclear Facility Components BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - GENERAL REQUIREMENTS FOR DIVISION 1 AND DIVISION 2 |
| BS EN 1290:1998 | Non-destructive examination of welds. Magnetic particle examination of welds |
| BS EN 1712:1997 | Non-destructive examination of welds. Ultrasonic examination of welded joints. Acceptance levels |
| ASME PV CODE 3 DIV 3 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - CONTAINMENT SYSTEMS FOR TRANSPORTATION AND STORAGE OF SPENT NUCLEAR FUEL AND HIGH-LEVEL RADIOACTIVE MATERIAL |
| ASME PV CODE 3 NC DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - CLASS 2 COMPONENTS |
| BS EN 1435:1997 | Non-destructive examination of welds. Radiographic examination of welded joints |
| BS EN 1714:1998 | Non destructive testing of welded joints. Ultrasonic testing of welded joints |
| API 2A : 1986 | RECOMMENDED PRACTICE FOR PLANNING, DESIGNING AND CONSTRUCTING FIXED OFFSHORE PLATFORMS |
| ASME PV CODE 3 NB DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - CLASS 1 COMPONENTS |
| BS ISO 12108:2012 | Metallic materials. Fatigue testing. Fatigue crack growth method |
| DD ENV 1999-1.1 : DRAFT DEC 2000 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 101: GENERAL RULES - GENERAL RULES AND RULES FOR BUILDINGS |
| ASME PV CODE 3 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - CODE FOR CONCRETE CONTAINMENTS |
| BS EN ISO 6520-1:2007 | Welding and allied processes. Classification of geometric imperfections in metallic materials Fusion welding |
| BS EN 1289:1998 | Non-destructive examination of welds. Penetrant testing of welds. Acceptance levels |
| DD ENV 1993-1.3 : 2001 AMD 13403 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1.3: GENERAL RULES - SUPPLEMENTARY RULES FOR COLD FORMED THIN GAUGE MEMBERS AND SHEETING |
| DD ENV 1999-2:2000 | Eurocode 9. Design of aluminium structures Structures susceptible to fatigue |
| DD ENV 1993-1.1 : DRAFT NOV 1992 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - GENERAL RULES AND RULES FOR BUILDINGS (TOGETHER WITH UNITED KINGDOM NATIONAL APPLICATION DOCUMENT) |
| BS EN 571-1:1997 | Non-destructive testing. Penetrant testing General principles |
| ASME PV CODE 3 NE DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - CLASS MC COMPONENTS |
| ASME PV CODE 3 APP DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - APPENDICES |
| API 579-1 : 2016 | FITNESS-FOR-SERVICE |
| BS EN 10002-5:1992 | Tensile testing of metallic materials Method of test at elevated temperatures |
| PD 6525-1:1990 | Elevated temperature properties for steels for pressure purposes. Stress rupture properties |
| BS EN 10002-1:2001 | Tensile testing of metallic materials Method of test at ambient temperature |
| ASME PV CODE 3 NG DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - CORE SUPPORT STRUCTURES |
| DD ENV 1993-1.2 : DRAFT 2001 REPRINT | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1.2: GENERAL RULES - STRUCTURAL FIRE DESIGN |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.